Allied-telesis SwitchBlade x8106 Manuel d'utilisateur

613-001835 Rev. ASwitchBlade x8106Layer 3+ Chassis Switch AT-SBx8106 Chassis AT-SBx81GT24 Line Card AT-SBx81GT40 Line Card AT-SBx81GP24 PoE Line C

List of Figures10Figure 50: Unlocking the Handle on the AT-SBxPWRSYS1 Power Supply ...

Chapter 4: Installing the Power Supplies1004. Check the model name, shown in Figure 55, to verify the module.If the module is the AT-SBxPWRSYS1 System

SwitchBlade x8106 Chassis Switch Installation Guide101Figure 57. Inserting the AT-SBxPWRPOE1 Power Supply

Chapter 4: Installing the Power Supplies1027. Lower the locking handle of the power supply module to secure the module in the slot, as shown in Figure

SwitchBlade x8106 Chassis Switch Installation Guide103Installing the AT-SBxPWRSYS1 DC Power SupplyThis section contains the installation procedure for

Chapter 4: Installing the Power Supplies104Figure 59. Removing the Blank Slot Cover from Power Supply Slot C3. Remove the power supply from the shippi

SwitchBlade x8106 Chassis Switch Installation Guide105Figure 60. Items Included with the AT-SBxPWRSYS1 DC Power Supply ModuleNoteStore the packaging m

Chapter 4: Installing the Power Supplies106Figure 61. Loosening the Handle locking Screw on the AT-SBxPWRPOE1 DC Power Supply5. Raise the locking hand

SwitchBlade x8106 Chassis Switch Installation Guide107Figure 63. Inserting the AT-SBxPWRSYS1 DC Power Supply

Chapter 4: Installing the Power Supplies1087. Lower the locking handle of the power supply module to secure the module in the slot, as shown in Figure

109Chapter 5Installing the AT-SBx81CFC400 Controller and Ethernet Line CardsThis chapter describes how to install the controller and Ethernet line car

SwitchBlade x8106 Chassis Switch Installation Guide11Figure 110: Attaching the Bare Grounding Wire to the Grounding Post...

Chapter 5: Installing the AT-SBx81CFC400 Controller and Ethernet Line Cards110Guidelines to Handling the Controller and Line CardsPlease observe the f

SwitchBlade x8106 Chassis Switch Installation Guide111Figure 65. Aligning Card in SlotCORRECTINCORRECTINCORRECT

Chapter 5: Installing the AT-SBx81CFC400 Controller and Ethernet Line Cards112Installing the AT-SBx81CFC400 Controller Fabric CardThis section contain

SwitchBlade x8106 Chassis Switch Installation Guide113Figure 67. Items Included with the AT-SBx81CFC400 Controller Fabric CardNoteStore the packaging

Chapter 5: Installing the AT-SBx81CFC400 Controller and Ethernet Line Cards114Figure 69. Opening the Locking Handles on the AT-SBx81CFC400 Controller

SwitchBlade x8106 Chassis Switch Installation Guide115Figure 71. Aligning the AT-SBx81CFC400 Card in the Chassis Slot7. Slowly and carefully slide the

Chapter 5: Installing the AT-SBx81CFC400 Controller and Ethernet Line Cards116Figure 72. Closing the Locking Levers on the AT-SBx81CFC400 Controller F

SwitchBlade x8106 Chassis Switch Installation Guide117Figure 73. Tightening the Thumb Screws on the AT-SBx81CFC400 Card10. Tighten the screws with a #

Chapter 5: Installing the AT-SBx81CFC400 Controller and Ethernet Line Cards118Installing the Ethernet Line CardsThis section contains the installation

SwitchBlade x8106 Chassis Switch Installation Guide119Figure 74. Removing an Ethernet Line Card from the Anti-static Bag4. Align the line card with th

List of Figures12

Chapter 5: Installing the AT-SBx81CFC400 Controller and Ethernet Line Cards120CautionKeep the card level with the chassis as you slide it into the slo

SwitchBlade x8106 Chassis Switch Installation Guide121Figure 77. Tightening the Thumb Screws on an Ethernet Line Card8. Tighten the two screws with a

Chapter 5: Installing the AT-SBx81CFC400 Controller and Ethernet Line Cards122Installing the Blank Slot CoversAfter installing the AT-SBx81CFC400 Cont

SwitchBlade x8106 Chassis Switch Installation Guide123Figure 79. Tightening the Thumbscrews on a Blank Slot Cover3. Tighten the two screws with a # 2

Chapter 5: Installing the AT-SBx81CFC400 Controller and Ethernet Line Cards124

125Chapter 6Installing the Transceivers and Cabling the PortsThis chapter describes how to install the fiber optic transceivers and attach the cables

Chapter 6: Installing the Transceivers and Cabling the Ports126Cabling Guidelines for the Twisted Pair Ports on the AT-SBx81GT24, AT-SBx81GP24, and AT

SwitchBlade x8106 Chassis Switch Installation Guide127 The default wiring configuration of the ports is automatic MDIX detection, which configures th

Chapter 6: Installing the Transceivers and Cabling the Ports128Figure 81. Connecting Cables to Ports on the AT-SBx81GT40 Line CardRelease tabConnectin

SwitchBlade x8106 Chassis Switch Installation Guide129Guidelines to Installing SFP and SFP+ TransceiversPlease review the following guidelines before

13Table 1. Twisted Pair Cable for the AT-SBx81GT24 and AT-SBx81GT40 Line Cards ...33Table 2. Twi

Chapter 6: Installing the Transceivers and Cabling the Ports130Installing SFP Transceivers in the AT-SBx81GS24a Line CardPlease review the information

SwitchBlade x8106 Chassis Switch Installation Guide1313. To install the transceiver in an SFP slot on the top row of the line card, orient the transce

Chapter 6: Installing the Transceivers and Cabling the Ports132Figure 85. Removing the Dust Cover from the SFP Transceiver in the AT-SBx81GS24a Line C

SwitchBlade x8106 Chassis Switch Installation Guide1337. Connect the fiber optic cable to the port on the transceiver, as shown in Figure 87. The conn

Chapter 6: Installing the Transceivers and Cabling the Ports134Installing SFP+ Transceivers in the AT-SBx81XS6 Line CardPlease review the information

SwitchBlade x8106 Chassis Switch Installation Guide135Figure 89. Handle on SFP+ Transceiver3. Slide the transceiver into the slot until it clicks into

Chapter 6: Installing the Transceivers and Cabling the Ports136Figure 91. Removing the Dust Cover from an SFP+ Transceiver in the AT-SBx81XS6 Line Car

SwitchBlade x8106 Chassis Switch Installation Guide1376. Connect the fiber optic cable to the port on the transceiver, as shown in Figure 93. The conn

Chapter 6: Installing the Transceivers and Cabling the Ports138Installing AT-SP10TW Cables in the AT-SBx81XS6 Line CardThis procedure explains how to

SwitchBlade x8106 Chassis Switch Installation Guide139Figure 95. Release Tab on the AT-SBx81XS6 Line Card3. Slide the connector into the slot until it

List of Tables14

Chapter 6: Installing the Transceivers and Cabling the Ports140NoteTo remove the connector and cable from the SFP+ slot, gently push on the connector,

SwitchBlade x8106 Chassis Switch Installation Guide141Cabling the NET MGMT Port on the AT-SBx81CFC400 CardThe controller card must have access to your

Chapter 6: Installing the Transceivers and Cabling the Ports142This setting is appropriate for port if it is connected to a network device that also s

143Chapter 7Powering On the ChassisThis chapter describes how to power on the chassis and monitor the initialization process. The chapter contains the

Chapter 7: Powering On the Chassis144Verifying the InstallationPlease perform the following procedure before powering on the chassis:1. Verify that th

SwitchBlade x8106 Chassis Switch Installation Guide145Powering On the AT-SBxPWRSYS1 AC Power SupplyThe procedure in this section explains how to power

Chapter 7: Powering On the Chassis146Figure 98. Connecting the AC Power Cord for the AT-SBxPWRSYS1 AC Power Supply3. Use the twist tie included with t

SwitchBlade x8106 Chassis Switch Installation Guide147Figure 99. Securing the Power Cord for the AT-SBxPWRSYS1 AC Power Supply to an Anchor4. Connect

Chapter 7: Powering On the Chassis148Powering On the AT-SBxPWRPOE1 Power SupplyIf you have not already installed the AT-SBxPWRPOE1 Power Supplies, ref

SwitchBlade x8106 Chassis Switch Installation Guide1493. Use the twist tie that comes with the power supply to secure the cord to an anchor on the cha

15PrefaceThis guide contains the hardware installation instructions for the Layer 3+ SwitchBlade x8106 Chassis Switch. The preface contains the follow

Chapter 7: Powering On the Chassis150Figure 102. Dress and Secure AC Power Cords6. Go to “Monitoring the Initialization Process” on page 177.

SwitchBlade x8106 Chassis Switch Installation Guide151Powering On the AT-SBxPWRSYS1 DC System Power SupplyThis section contains instructions on how to

Chapter 7: Powering On the Chassis152The components of the power supply are identified in Figure 103.Figure 103. Components of the AT-SBxPWRSYS1 DC Po

SwitchBlade x8106 Chassis Switch Installation Guide153Choosing aMethod forAttaching theGrounding WireYou may attach the grounding wire to the power su

Chapter 7: Powering On the Chassis1543. Use an 8 mm wrench to remove the grounding post nut and washer, shown in Figure 107, from the power supply.Fig

SwitchBlade x8106 Chassis Switch Installation Guide155Figure 108. Installing the Grounding Wire5. Connect the other end of the grounding wire to the b

Chapter 7: Powering On the Chassis156Connecting theGrounding Wirewith Bare WireTo attach the grounding wire to the power supply with bare wire, perfor

SwitchBlade x8106 Chassis Switch Installation Guide1574. Secure the wire with the nut and washer removed in step 2, and an 8 mm wrench, as shown in Fi

Chapter 7: Powering On the Chassis158Choosing aMethod forAttaching thePower WiresThe AT-SBxPWRSYS1 DC Power Supply comes with the two sets of power wi

SwitchBlade x8106 Chassis Switch Installation Guide159Figure 113. Stripping the Power WiresNoteYou must use stranded wires with the terminal lugs. You

Preface16Safety Symbols Used in this DocumentThis document uses the following conventions.NoteNotes provide additional information.CautionCautions inf

Chapter 7: Powering On the Chassis160Figure 115. On/Off Switch on the AT-SBxPWRSYS1 DC Power Supply4. Use a #1 Phillips-head screwdriver to loosen the

SwitchBlade x8106 Chassis Switch Installation Guide161Figure 116. Opening the Plastic Cover5. Use a #3 Phillips-head screwdriver to remove the two scr

Chapter 7: Powering On the Chassis162Figure 117. Removing the Terminal Screws6. With a #3 Phillips-head screwdriver, connect the positive (+) power le

SwitchBlade x8106 Chassis Switch Installation Guide163Figure 118. Connecting the Positive (+) Power Wire with a Straight Terminal7. With a #3 Phillips

Chapter 7: Powering On the Chassis164Figure 119. Connecting the Negative (-) Power Wire with a Straight TerminalWarningCheck to see if there are any e

SwitchBlade x8106 Chassis Switch Installation Guide165Figure 120. Closing the Plastic Cover over the Terminal ConnectorsCautionDo not over tighten the

Chapter 7: Powering On the Chassis166Figure 121. Tightening the Handle Locking Screw10. Before attaching the power wires from the power supply to the

SwitchBlade x8106 Chassis Switch Installation Guide167Connecting theDC Power Wireswith the RightAngle TerminalsTo connect the DC power wires to the po

Chapter 7: Powering On the Chassis1684. Using a #1 Phillips-head screwdriver, remove the two screws that secure the plastic cover over the positive an

SwitchBlade x8106 Chassis Switch Installation Guide169Figure 125. Removing the Terminal Screws6. With a #3 Phillips-head screwdriver, connect the posi

SwitchBlade x8106 Chassis Switch Installation Guide17Contacting Allied TelesisIf you need assistance with this product, you may contact Allied Telesis

Chapter 7: Powering On the Chassis170Figure 126. Connecting the Positive (+) Power Wire with a Right Angle Terminal7. With a #3 Phillips-head screwdri

SwitchBlade x8106 Chassis Switch Installation Guide171Figure 127. Connecting the Negative (-) Power Wire with a Right Angle TerminalWarningCheck to se

Chapter 7: Powering On the Chassis172Figure 128. Tightening the Handle Locking Screw9. Before attaching the power wires from the power supply to the c

SwitchBlade x8106 Chassis Switch Installation Guide173Connecting BareDC Power WiresTo attach bare lead wires to the positive and negative terminals on

Chapter 7: Powering On the Chassis174Figure 130. Connecting the Positive Lead Wire5. Wrap the negative lead wire clockwise around the remaining termin

SwitchBlade x8106 Chassis Switch Installation Guide175Figure 131. Connecting the Negative Lead WireAllied Telesis recommends tightening the screw to 3

Chapter 7: Powering On the Chassis1767. With a #2 Phillips-head screwdriver, tighten the handle locking screw to secure the power supply to the chassi

SwitchBlade x8106 Chassis Switch Installation Guide177Monitoring the Initialization ProcessThe line and controller cards perform an initialization pro

Chapter 7: Powering On the Chassis178Figure 132. Switch Initialization MessagesVerifying release... OKBooting...Starting base/first... [ OK ]Mounting

SwitchBlade x8106 Chassis Switch Installation Guide179Figure 133. Switch Initialization Messages (Continued)auth, bgpd, cntrd, epsr, exfx, hostd, hsli

Preface18

Chapter 7: Powering On the Chassis180

181Chapter 8Verifying the Hardware Operations of the ChassisThis chapter describes how to verify the operations of the chassis. The chapter contains t

Chapter 8: Verifying the Hardware Operations of the Chassis182Using the LEDs to Verify the ChassisAfter powering on the chassis for the first time and

SwitchBlade x8106 Chassis Switch Installation Guide183preventing them from completing the initialization process. Power off the chassis and replace th

Chapter 8: Verifying the Hardware Operations of the Chassis184Using Local Management to Verify the ChassisThis section explains how to use the command

SwitchBlade x8106 Chassis Switch Installation Guide1852. Connect the other end of the cable to an RS-232 port on a terminal or personal computer with

Chapter 8: Verifying the Hardware Operations of the Chassis186Figure 135. SHOW VERSION Command2. Compare the version number displayed by the SHOW VERS

SwitchBlade x8106 Chassis Switch Installation Guide1876. To check the status of PoE on the ports of the AT-SBx81GP24 Line Card, use the SHOW POWER-INL

Chapter 8: Verifying the Hardware Operations of the Chassis188

189Chapter 9TroubleshootingThis chapter contains information on how to troubleshoot the SwitchBlade x8106 product.NoteIf you are unable to resolve a h

19Chapter 1OverviewThis chapter describes the Layer 3+ SwitchBlade x8106 Chassis Switch in the following sections: “Introduction” on page 20 “AT-SBx

Chapter 9: Troubleshooting190AT-SBxPWRSYS1 and AT-SBxPWRPOE1 AC Power SuppliesA power supply is operating normally when its AC and DC LEDs are solid g

SwitchBlade x8106 Chassis Switch Installation Guide191AT-SBxPWRSYS1 DC Power SupplyIf you suspect a problem with the DC power supply, examine its LEDs

Chapter 9: Troubleshooting192software version on the control card, refer to “Using Local Management to Verify the Chassis” on page 184 and “AlliedWare

SwitchBlade x8106 Chassis Switch Installation Guide193Ethernet Line CardsA quick and easy way to check the overall heath of the Ethernet line cards in

Chapter 9: Troubleshooting194 You can obtain card status information with the SwitchBlade x8106 Management Software and the SHOW CARD command, as fol

SwitchBlade x8106 Chassis Switch Installation Guide195Twisted Pair PortsThe ports on the AT-SBx81GT24 and AT-SBx81GP24 Line Cards have L/A LEDs that a

Chapter 9: Troubleshooting196 The default duplex mode setting for the ports is Auto-Negotiation. This setting is appropriate for ports connected to n

SwitchBlade x8106 Chassis Switch Installation Guide197Power Over EthernetThis section applies only to the AT-SBx81GP24 Line Card. Each port has two LE

Chapter 9: Troubleshooting198 Use the SHOW POE CARD command to determine whether the switch has reach its maximum power budget. Try connecting the P

SwitchBlade x8106 Chassis Switch Installation Guide199Fiber Optic TransceiversThe L/A LEDs on the AT-SBx81GS24a and AT-SBx81XS6 Line Cards are solid o

Copyright  2013 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Chapter 1: Overview20IntroductionThe SwitchBlade x8106 product is a modular Layer 3+ Ethernet switch. The main components are the AT-SBx8106 Chassis,

Chapter 9: Troubleshooting200AT-SBx81CFC400 Controller Fabric CardIf the chassis has one controller card and the card fails, all network operations st

SwitchBlade x8106 Chassis Switch Installation Guide201AT-SBxFAN06 Fan ModuleThe AT-SBxFAN06 Fan Module is operating correctly when the POWER LED on th

Chapter 9: Troubleshooting202Local (Out-of-Band) Management SessionIf you are unable to establish a local (out-of-band) management session with the sw

SwitchBlade x8106 Chassis Switch Installation Guide203Power Supply Interfaces (Opto-couplers)The two power supply interfaces in the lower right corner

Chapter 9: Troubleshooting204

205Chapter 10Replacing ModulesThis chapter contains procedures on how to replace modules in the unit. The chapter contains the following sections: “R

Chapter 10: Replacing Modules206Replacing AT-SBxPWRSYS1 AC and AT-SBxPWRPOE1 Power SuppliesThis section contains the procedure for removing AT-SBxPWRS

SwitchBlade x8106 Chassis Switch Installation Guide2072. Lift the locking hand on the power supply. Refer to Figure 138.Figure 138. Lifting the Lockin

Chapter 10: Replacing Modules208Figure 139. Removing the Power Supply from the Chassis4. Do one of the following: To install a new power supply, refe

SwitchBlade x8106 Chassis Switch Installation Guide209Figure 140. Installing a Blank Power Supply Slot Cover6. Lower the locking handle to secure the

SwitchBlade x8106 Chassis Switch Installation Guide21Figure 3. Ethernet Line Cards and Controller Card (Continued)Figure 4 illustrates the power suppl

Chapter 10: Replacing Modules210Figure 141. Lowering the Locking Handle on the Power Supply Slot Cover

SwitchBlade x8106 Chassis Switch Installation Guide211Replacing the AT-SBxPWRSYS1 DC Power SupplyTo remove an AT-SBxPWRSYS1 DC Power Supply from the c

Chapter 10: Replacing Modules212NoteIf the power wires are connected to the terminal block with the right angle terminals, go to step 5.4. Use a #1 sc

SwitchBlade x8106 Chassis Switch Installation Guide213Figure 144. Removing the Negative Lead Wire6. Use a #3 screwdriver to remove the positive (+) le

Chapter 10: Replacing Modules214Figure 145. Removing the Positive Lead Wire from the Terminal Block7. Reinstall the two screws on the negative (-) and

SwitchBlade x8106 Chassis Switch Installation Guide215Figure 146. Reinstalling the Screws on the Positive and Negative Terminals8. Slide the plastic c

Chapter 10: Replacing Modules216Figure 147. Closing the Plastic Cover9. Use an 8 mm wrench to remove the grounding wire from the grounding post. Refer

SwitchBlade x8106 Chassis Switch Installation Guide217Figure 148. Removing the Grounding Wire10. Reinstall the nut and washer on the grounding post. R

Chapter 10: Replacing Modules218Figure 149. Reinstalling the Nut and Washer on the Grounding Post11. Lift the locking handle and slide the power suppl

SwitchBlade x8106 Chassis Switch Installation Guide219Figure 150. Lifting the Locking Handle and Removing the Power Supply12. Do one of the following:

Chapter 1: Overview22Figure 5 illustrates the fan module.Figure 5. Fan ModuleAT-SBxFAN06 Module. The cooling module for the chassis.

Chapter 10: Replacing Modules220Figure 151. Installing a Blank Power Supply Slot Cover14. Lower the locking handle to secure the slot cover to the slo

SwitchBlade x8106 Chassis Switch Installation Guide221Figure 152. Lowering the Locking Handle on the Power Supply Slot Cover

Chapter 10: Replacing Modules222Replacing Ethernet Line CardsThis section contains the procedure for replacing Ethernet line cards in the chassis.Note

SwitchBlade x8106 Chassis Switch Installation Guide223instructions, refer to “Installing the Blank Slot Covers” on page 122. If you do not plan to im

Chapter 10: Replacing Modules224Replacing the AT-SBx81CFC400 Controller Fabric CardThis section contains the procedure for replacing a controller card

SwitchBlade x8106 Chassis Switch Installation Guide225NoteYou should not replace a controller card in a chassis that has two controller cards while th

Chapter 10: Replacing Modules226Replacing the AT-SBxFAN06 Fan ModuleThis section contains the procedures for replacing the AT-SBxFAN06 Fan Module. The

SwitchBlade x8106 Chassis Switch Installation Guide227Figure 153. Loosening the Screw on the AT-SBxFAN06 Fan Module3. Carefully pull on the handle to

Chapter 10: Replacing Modules2284. Slowly pull the module out 25 mm (1 in.). Refer to Figure 155.Figure 155. Withdrawing the AT-SBxFAN06 Fan Module 25

SwitchBlade x8106 Chassis Switch Installation Guide229Figure 156. Removing the AT-SBxFAN06 Fan Module from the ChassisInstalling a NewAT-SBxFAN06Fan M

SwitchBlade x8106 Chassis Switch Installation Guide23AT-SBx8106 ChassisThe AT-SBx8106 Chassis is a 4RU unit with slots for four Ethernet line cards, t

Chapter 10: Replacing Modules230Figure 157. Installing a New AT-SBxFAN06 Fan Module2. When you feel the fan module make contact with the connector on

SwitchBlade x8106 Chassis Switch Installation Guide231Figure 158. Securing the AT-SBxFAN06 Fan Module on the Backplane Connector3. With a #2 Phillips-

Chapter 10: Replacing Modules232

233Appendix ATechnical SpecificationsPhysical SpecificationsDimensions (W x D x H)Weight (Kilograms)Table 21. Product DimensionsAT-SBx8106 Chassis 4

Appendix A: Technical Specifications234AT-SBx81GS24a SFP Line Card 1.06 kg (2.34 lb)AT-SBx81XS6 SFP+ Line Card 1.06 kg (2.34 lb)AT-SBx81CFC400 Control

SwitchBlade x8106 Chassis Switch Installation Guide235Environmental SpecificationsNoteThe acoustic noise was measured at 40° C with the following prod

Appendix A: Technical Specifications236Power SpecificationsAC Voltage, Frequency Requirements (Volts, Hertz)CC Voltage RequirementsTypical power savin

SwitchBlade x8106 Chassis Switch Installation Guide237Maximum power supply efficiency (based on 100V input voltage)Heat dissipation (British Thermal U

Appendix A: Technical Specifications238PoE ModeSafety and Electromagnetic Emissions CertificationsSafety and Electromagnetic Emissions:Table 32. Ava

SwitchBlade x8106 Chassis Switch Installation Guide239Port PinoutsThis section lists the port pinouts for the AT-SBx81GT24, AT-SBx81GT40, and AT-SBx81

Chapter 1: Overview24Figure 7. Rear View of the AT-SBx8106 ChassisFigure 8 is an example of a fully populated chassis.Figure 8. AT-SBx8106 Chassis wit

Appendix A: Technical Specifications240Table 37 lists the port pin signals when a 10/100/1000Base-T port is operating at 1000 Mbps.Table 37. 1000Bas

SwitchBlade x8106 Chassis Switch Installation Guide25Figure 9. Ethernet Line and Controller Cards SlotsSlots 1 to 4 are for the Ethernet line cards. T

Chapter 1: Overview26power so that the chassis can support more powered devices and adds power redundancy. For more information, refer to “Power over

SwitchBlade x8106 Chassis Switch Installation Guide27AT-SBx81GT24 Line CardThe AT-SBx81GT24 Line Card, shown in Figure 11, is a Gigabit Ethernet switc

Chapter 1: Overview28AT-SBx81GT40 Line CardThe AT-SBx81GT40 Line Card, shown in Figure 12, is a Gigabit Ethernet switch.Figure 12. AT-SBx81GT40 Line C

SwitchBlade x8106 Chassis Switch Installation Guide29AT-SBx81GP24 PoE Line CardThe AT-SBx81GP24 PoE Line Card, shown in Figure 13, is a Gigabit Ethern

3Electrical Safety and Emissions StandardsThis product meets the following standards.EMI/RFI Emissions: FCC Class A, EN55022 Class A, EN61000-3-2, EN6

Chapter 1: Overview30AT-SBx81GS24a SFP Line CardThe AT-SBx81GS24a SFP Line Card, shown in Figure 14, is a Gigabit Ethernet switch.Figure 14. AT-SBx81G

SwitchBlade x8106 Chassis Switch Installation Guide31AT-SBx81XS6 SFP+ Line CardThe AT-SBx81XS6 Line Card, shown in Figure 15, is a 10 Gigabit Ethernet

Chapter 1: Overview3210/100/1000Base-T Twisted Pair PortsThis section applies to the 10/100/1000Base-T ports on the AT-SBx81GT24, AT-SBx81GT40, and AT

SwitchBlade x8106 Chassis Switch Installation Guide33MaximumDistanceThe ports have a maximum operating distance of 100 meters (328 feet).CableRequirem

Chapter 1: Overview34Automatic MDIXDetectionThe 10/100/1000 Mbps twisted-pair ports on the AT-SBx81GT24, AT-SBx81GT40, and AT-SBx81GP24 Line Cards are

SwitchBlade x8106 Chassis Switch Installation Guide35Power over Ethernet on the AT-SBx81GP24 Line CardThis section applies to the AT-SBx81GP24 PoE Lin

Chapter 1: Overview36Power Budgeting The power for PoE on the ports on the AT-SBx81GP24 Line Card is provided by the AT-SBxPWRPOE1 Power Supply. It ca

SwitchBlade x8106 Chassis Switch Installation Guide37PDs that comply with the IEEE 802.3af and 802.3at standards typically support both power delivery

Chapter 1: Overview38Port LEDs on the Ethernet Line CardsThe following sections define the port LEDs on the Ethernet line cards.AT-SBx81GT24Line CardE

SwitchBlade x8106 Chassis Switch Installation Guide39AT-SBx81GT40Line CardThe LEDs for a port on the AT-SBx81GT40 Line Card are found on the RJ point

SwitchBlade x8106 Chassis Switch Installation Guide4Translated Safety StatementsImportant: The  indicates that a translation of the safety statement

Chapter 1: Overview40Figure 18. Port LEDs on an RJ Point 5 Cable Connector for the AT-SBx81GT40 Line CardTable 6. Port LEDs on the AT-SBx81GT40 Line

SwitchBlade x8106 Chassis Switch Installation Guide41AT-SBx81GP24Line CardEach port on the AT-SBx81GP24 PoE Line Card has two LEDs. The LEDs are shown

Chapter 1: Overview42AT-SBx81GS24aLine CardThe SFP slots on the AT-SBx81GS24a SFP Line Card have one LED each, as shown in Figure 20 and described in

SwitchBlade x8106 Chassis Switch Installation Guide43AT-SBx81XS6Line CardThe AT-SBx81XS6 Line Card has one LED for each SFP+ slot. The LED is shown in

Chapter 1: Overview44AT-SBx81CFC400 Controller Fabric CardThe AT-SBx81CFC400 Controller Fabric Card has three primary functions: Chassis Management —

SwitchBlade x8106 Chassis Switch Installation Guide45The components on the card are identified in Figure 22.Figure 22. AT-SBx81CFC400 Controller Fabri

Chapter 1: Overview46Table 10. SYS (System) Status LEDsLED State DescriptionCFCSolid Green Indicates that the AT-SBx81CFC400 Controller Fabric Card

SwitchBlade x8106 Chassis Switch Installation Guide47SBx STATUSLEDsThe SBx LINECARD STATUS LEDs display general status information about the Ethernet

Chapter 1: Overview48eco-friendlyButtonYou may use the eco-friendly button on the controller card to turn the LEDs on or off. You may turn off the LED

SwitchBlade x8106 Chassis Switch Installation Guide49NoteThe available bandwidth across the backplane of the chassis is reduced from 80 Gbps per slot

5Preface ...

Chapter 1: Overview50Table 12. Features that Use the NET MGMT PortFeature DescriptionPing Used to test the NET MGMT port for network connectivity.FT

SwitchBlade x8106 Chassis Switch Installation Guide51The NET MGMT port has a standard RJ-45 8-pin connector and operates at 10, 100, or 1000 Mbps in e

Chapter 1: Overview52USB Port The USB port supports a flash drive. You may use a flash drive to perform the following management functions: Store bac

SwitchBlade x8106 Chassis Switch Installation Guide53AT-SBxPWRSYS1 AC Power SupplyThe AT-SBxPWRSYS1 AC Power Supply, shown in Figure 23, is the power

Chapter 1: Overview54DCSolid Green The power supply is providing DC power that is within the normal operating range.Off The power supply is not genera

SwitchBlade x8106 Chassis Switch Installation Guide55AT-SBxPWRPOE1 Power SupplyThe AT-SBxPWRPOE1 Power Supply, shown in Figure 24, provides the PoE po

Chapter 1: Overview56Table 15. AT-SBxPWRPOE1 Power Supply LEDsLED State DescriptionACSolid Green The power supply is receiving AC power that is with

SwitchBlade x8106 Chassis Switch Installation Guide57AT-SBxPWRSYS1 DC Power SupplyThe AT-SBxPWRSYS1 DC Power Supply, shown in Figure 25, is a DC versi

Chapter 1: Overview58NoteGiven that the AT-SBxPWRSYS1 DC Power Supply is not compatible with the AT-SBxPWRPOE1 AC Power Supply, a chassis that contain

SwitchBlade x8106 Chassis Switch Installation Guide59AT-SBxFAN06 ModuleThe AT-SBxFAN06 Module is the cooling unit for the chassis. Refer to Figure 26.

Contents6AT-SBxPWRSYS1 DC Power Supply... 5

Chapter 1: Overview60Power Supply Interfaces (Opto-couplers)The chassis has two power supply interfaces, also referred to as opto-couplers, in the low

SwitchBlade x8106 Chassis Switch Installation Guide61Table 18. Power Supply Interface LEDLED State DescriptionPowerSolid Green The interface is oper

Chapter 1: Overview62AlliedWare Plus Software Releases for the Hardware ComponentsTable 19 lists the releases of the AlliedWare Plus Operating System

63Chapter 2Safety Precautions and Site RequirementsThis chapter contains the safety precautions and guidelines for selecting a site for the chassis. T

Chapter 2: Safety Precautions and Site Requirements64Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to in

SwitchBlade x8106 Chassis Switch Installation Guide65NotePluggable Equipment. The socket outlet shall be installed near the equipment and shall be eas

Chapter 2: Safety Precautions and Site Requirements66WarningMounting of the equipment in the rack should be such that a hazardous condition is not cre

SwitchBlade x8106 Chassis Switch Installation Guide67WarningReliable earthing of rack-mounted equipment should be maintained. Particular attention sho

Chapter 2: Safety Precautions and Site Requirements68Selecting a Site for the SwitchBlade x8106Please perform the following procedure to determine the

SwitchBlade x8106 Chassis Switch Installation Guide69Figure 28. 100 - 125 VAC 125 V NEMA 5-20 Plug and Receptacle

SwitchBlade x8106 Chassis Switch Installation Guide7Monitoring the Initialization Process ...

Chapter 2: Safety Precautions and Site Requirements70Installation Tools and MaterialThis section lists the tools and material you need to supply to in

71Chapter 3Installing the Chassis in an Equipment RackThis chapter describes how to install the AT-SBx8106 Chassis in an equipment rack. This chapter

Chapter 3: Installing the Chassis in an Equipment Rack72Required Tools and MaterialYou need the following tools and material to install the product in

SwitchBlade x8106 Chassis Switch Installation Guide73Preparing the Equipment RackTo prepare the equipment rack for the AT-SBx8106 Chassis, perform the

Chapter 3: Installing the Chassis in an Equipment Rack74Figure 29. Reserving Vertical Rack Space190.0 mm (7.5“)152.4 mm (6”0)342.4 mm (13.5”)

SwitchBlade x8106 Chassis Switch Installation Guide753. Identify the lowest 1/2” screw hole pattern on the rack mounting rails within the space reserv

Chapter 3: Installing the Chassis in an Equipment Rack76Unpacking the AT-SBx8106 ChassisTo unpack the AT-SBx8106 Chassis, perform the following proced

SwitchBlade x8106 Chassis Switch Installation Guide77Figure 32. Components of the AT-SBx8106 Chassis (Continued)Two equipment rack brackets pre-instal

Chapter 3: Installing the Chassis in an Equipment Rack78Removing the Rubber FeetThe chassis comes with rubber feet on the base panel for tabletop inst

SwitchBlade x8106 Chassis Switch Installation Guide79Figure 34. Removing the Rubber Feet3. Turn the chassis over.Go to the next procedure, “Adjusting

Contents8

Chapter 3: Installing the Chassis in an Equipment Rack80Adjusting the Equipment Rack BracketsThe chassis has two pre-installed equipment rack brackets

SwitchBlade x8106 Chassis Switch Installation Guide81Figure 35. Rack Mounting Bracket LocationsFigure 36. Rack Bracket Locations for Reverse Position

Chapter 3: Installing the Chassis in an Equipment Rack82Installing the Chassis in the Equipment RackThe procedure in this section explains how to inst

SwitchBlade x8106 Chassis Switch Installation Guide832. Lift the AT-SBx8106 Chassis into the equipment rack and set the bottom of the equipment rack b

Chapter 3: Installing the Chassis in an Equipment Rack84Figure 38. Installing the Rack Mount Screws5. Tighten all six screws shown in Figure 39 on pag

SwitchBlade x8106 Chassis Switch Installation Guide85Figure 39. Tightening the Rack Mount Screws6. Go to “Removing the Shipping Brace” on page 86.Scre

Chapter 3: Installing the Chassis in an Equipment Rack86Removing the Shipping BraceNow that the chassis is installed in the equipment rack, you may re

SwitchBlade x8106 Chassis Switch Installation Guide87Installing the Chassis Grounding LugThis procedure explains how to connect a grounding wire to th

Chapter 3: Installing the Chassis in an Equipment Rack883. Insert one end of the grounding wire into the grounding lug, as shown in Figure 43, and use

89Chapter 4Installing the Power SuppliesThis chapter explains how to install the power supplies. It has the following sections: “Protecting Against E

9FiguresFigure 1: AT-SBx8106 Chassis ...

Chapter 4: Installing the Power Supplies90Protecting Against Electrostatic Discharge (ESD)To protect the equipment from damage by Electrostatic Discha

SwitchBlade x8106 Chassis Switch Installation Guide91Installing the AT-SBxPWRSYS1 AC System Power SupplyFor background information on the AT-SBxPWRSYS

Chapter 4: Installing the Power Supplies92Figure 47. Removing the Blank Slot Cover from Power Supply Slot C3. Remove the new AT-SBxPWRSYS1 Power Suppl

SwitchBlade x8106 Chassis Switch Installation Guide93Figure 48. Items Included with the AT-SBxPWRSYS1 Power Supply ModuleNoteStore the packaging mater

Chapter 4: Installing the Power Supplies944. Check the power supply for its model name, shown in Figure 49, to verify the module.If the module is the

SwitchBlade x8106 Chassis Switch Installation Guide956. Align and insert the AT-SBxPWRSYS1 Power Supply into the power supply slot. Figure 51 shows th

Chapter 4: Installing the Power Supplies967. Lower the power supply locking handle to secure the power supply to the chassis, as shown in Figure 52.Fi

SwitchBlade x8106 Chassis Switch Installation Guide97Installing the AT-SBxPWRPOE1 PoE Power SupplyThis section contains the installation procedure for

Chapter 4: Installing the Power Supplies98Figure 53. Removing the Blank Slot Cover from Power Supply Slot A3. Remove the power supply from the shippin

SwitchBlade x8106 Chassis Switch Installation Guide99Figure 54. Items Included with the AT-SBxPWRPOE1 Power Supply ModuleNoteStore the packaging mater