Allied-telesis x900 Series Switch and SwitchBlade x908 Manuel d'utilisateur

x900 Series Switch and SwitchBlade® x908Installation and Safety GuideAT-8948x900-48FEx900-48FE-Nx900-48FSAT-9924TAT-9924SPAT-9924Tsx900-12XT/Sx900-24X

Installation and Safety Guide9In a 19-inch rack1. Ensure the rack has sufficient space for the switch and its cables. For the switch’s requirements, s

x900 Series Switch and SwitchBlade® x90810Fitting a bracket on a SwitchBlade x908 switchFitting a bracket on all other x900 Series switches5. Mount th

Installation and Safety Guide11Applying Power to the SwitchPower supply bays are in the rear of the switch. Depending on the model, the switch may hav

x900 Series Switch and SwitchBlade® x908121. Plug the AC power cord that is provided into the power inlet on the PSU.2. Connect the power cord to the

Installation and Safety Guide13Warning When SBx908 devices are connected with VCS stacking cables (either HS-STK-CBL or XEM-STK-CBL), each individual

x900 Series Switch and SwitchBlade® x908148. Ensure that the circuit breaker is off for the supply circuit and the Run/Standby switch on the PSU. Rele

Installation and Safety Guide15PWR05 DC PWR05 DCPower supply specifications: functional range 40 to 60 V, 4 8 V nominal supports either positive gr

x900 Series Switch and SwitchBlade® x908165. Confirm that the switch is receiving power.Check that the PSU LED on the front panel of the switch corres

Installation and Safety Guide17Connecting to the SwitchAll x900 Series switches and the SwitchBlade x908 can be configured using the Command Line Inte

x900 Series Switch and SwitchBlade® x90818When x900-24XT, x900-24XT-N, x900-24XS, or SwitchBlade x908 switches are connected to form a virtual chassis

x900 Series Switch and SwitchBlade® x908 Installation and Safety Guide AT-8948 AT-9924Ts x900-48FE x900-12XT/S x900-48FE-N x900-24XT x900-48FS x900-24

Installation and Safety Guide195. Configure the switch.Refer to the AlliedWare Plus™ Operating System Software Reference for detailed information abou

x900 Series Switch and SwitchBlade® x90820Using the AlliedWare Plus Operating System GUIFollow this procedure to establish a connection to an x900 or

Installation and Safety Guide217. Save the configuration.Save the current configuration as the default startup configuration by using the commands:awp

x900 Series Switch and SwitchBlade® x90822Using the AlliedWare Operating System CLIDepending on the model, an ASYN0/CONSOLE and/or ETH0 port is on the

Installation and Safety Guide234. Change the password.A manager account with the default password is a serious security risk. Remember the new passwor

x900 Series Switch and SwitchBlade® x90824Using the AlliedWare Operating System GUIFollow this procedure to establish a connection to an AT-9900 serie

Installation and Safety Guide25Checking LEDsThe following LEDs report operations and faults on x900 Series and SwitchBlade x908 switches: “System LED

x900 Series Switch and SwitchBlade® x90826POWER Green The PSU is operating and supplying power to the switch. The voltage output is within specificati

Installation and Safety Guide27Stacking LEDsThe following table describes how LEDs on the SwitchBlade x908 report operations and faults on the rear pa

x900 Series Switch and SwitchBlade® x90828PWR05 LEDsThe following is a diagram of the LEDs in the PWR05 power supply units: PWR05 AC LEDsThe following

x900 Series Switch and SwitchBlade® x9082x900 Series Switch and SwitchBlade® x908 Installation and Safety Guide Document Number C613-04052-00 REV P© 2

Installation and Safety Guide29PWR05 DC LEDsThe following table describes LEDs on the PWR05 DC power supply unit for the SwitchBlade x908.LED State De

x900 Series Switch and SwitchBlade® x90830Obtaining Documentation and ResourcesThe complete document set for x900 Series switches and SwitchBlade x908

Installation and Safety Guide31AT-TFTP Server for Windows is a TFTP (Trivial File Transfer Protocol) server for transferring software versions, config

x900 Series Switch and SwitchBlade® x90832StandardsWhere applicable, the products in this document meet the following standards: Category Approval Age

Installation and Safety Guide33SafetyWARNING: In a domestic environment this product may cause radio interference in which case the user may be requir

x900 Series Switch and SwitchBlade® x90834Lithium Battery - Should be changed only by authorised service personnel. CAUTION: Danger of explosion if ba

Installation and Safety Guide35SicherheitWARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen hervorrufen. In diesem Fall müßte der Anwe

x900 Series Switch and SwitchBlade® x90836Lithium-Batterie - Sollte nur von einem geschulten qualifizierten Techniker ausgetauscht werden. VORSICHT: E

Installation and Safety Guide37SikkerhedADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves

x900 Series Switch and SwitchBlade® x90838med samme eller en tilsvarende type der anbefales af producenten. Kassér brugte batterier i overensstemmelse

Installation and Safety Guide3ContentsAbout this Guide ...

Installation and Safety Guide39VeiligheidWAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan

x900 Series Switch and SwitchBlade® x90840Lithium batterij. Mag alleen worden vervangen door een daartoe opgeleide en bevoegde technicus. OPGELET: Ge

Installation and Safety Guide41SécuritéMISE EN GARDE : dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques.

x900 Series Switch and SwitchBlade® x90842ATTENTION : RÉPARTITION DE LA CHARGE MÉCANIQUE - Le montage du matériel dans le bâti doit être effectué de t

Installation and Safety Guide43Remarque: Ce système peut fonctionner avec des systèmes C.C. dotés d’une mise à la terre positive ou négative. Turvalli

x900 Series Switch and SwitchBlade® x90844Litiumparisto - Vaihdon voi suorittaa vain koulutettu ja pätevä teknikko. Varoitus: Räjähdysvaara, jos paris

Installation and Safety Guide45Norme di SicurezzaAVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso

x900 Series Switch and SwitchBlade® x90846Batteria al litio - Va sostituita solo da un tecnico specializzato e qualificato. ATTENZIONE: l'errata

Installation and Safety Guide47SikkerhetADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette

x900 Series Switch and SwitchBlade® x90848ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale elektriske koder.Advarsel: VED TILK

x900 Series Switch and SwitchBlade® x9084About this GuideThis Installation and Safety Guide describes how to install and log in to the following switc

Installation and Safety Guide49SegurançaAVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser

x900 Series Switch and SwitchBlade® x90850Bateria de lítio - Só deve ser trocada por técnico qualificado e treinado. CUIDADO: Se a bateria não for dev

Installation and Safety Guide51SeguridadADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requ

x900 Series Switch and SwitchBlade® x90852ATENCION: CARGA MECANICA - El montaje del equipo en el bastidor debe realizarse de manera tal que no cause u

Installation and Safety Guide53Nota: Este sistema funcionará con sistemas de CC con conexión positiva o negativa a tierra. SäkerhetVARNING: Denna prod

x900 Series Switch and SwitchBlade® x90854Litium batteri - Får endast bytas av utbildade och kvalificerade tekniker. VARNING: Risk för explosion om fe

Installation and Safety Guide5The following items are shipped with each switch. Contact your authorised distributor or reseller if any are damaged or

x900 Series Switch and SwitchBlade® x9086Selecting a SiteBefore you install the switch, review the following considerations about its location. AT-89

Installation and Safety Guide7Installing the SwitchPorts on the switch are suitable only for connections within buildings (intra-building) and with ca

x900 Series Switch and SwitchBlade® x9088 All bare conductors must be coated with an appropriate antioxidant compound before making crimp connections