Allied-telesis AT-S60 Manuel d'utilisateur Page 296
- Page / 303
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 27: TACACS+ and RADIUS Commands
294
SHOW AUTHENTICATION
Syntax
show authentication
Parameters
None.
Description
Use this command to display the following information about the
authenticated protocols on the switch:
❑ Status - The status of your authenticated protocol: enabled or
disabled.
❑ Authentication Method - The authentication protocol activated
on your switch. Either TACACS+ or RADIUS protocols may be
active. The TACACS+ protocol is the default.
❑ The IP addresses of up to three authentication servers.
❑ The server encryption keys, if defined.
❑ TAC global secret - The global encryption key that applies to all
authentication servers. This is an optional parameter.
❑ Timeout - The length of the time, in seconds, before the switch
assumes the server will not respond.
Example
The following command displays authentication protocol information
on your switch:
show authentication
- Command Line 1
- User’s Guide 1
- Table of Contents 3
- How This Guide is Organized 9
- Features 11
- Security 11
- Document Conventions 12
- Contacting Allied Telesyn 14
- Starting a Command Line 16
- Management Session 16
- Starting a Management Session 17
- Command Formatting 19
- Basic Command-Line Commands 21
- CLEAR SCREEN 22
- LOGOFF and QUIT 23
- SAVE CONFIGURATION 25
- SET PROMPT 26
- SET SWITCH CONSOLEMODE 27
- SHOW USER 28
- Basic Switch Commands 29
- DISABLE DHCPBOOTP 31
- DISABLE TELNET 32
- ENABLE DHCPBOOTP 33
- ENABLE TELNET 34
- PURGE IP 36
- RESET ASYN 37
- RESET IP 38
- RESET IP ROUTE 39
- RESTART REBOOT 41
- RESTART SWITCH 42
- SET ASYN 43
- SET IP ROUTE 46
- SET PASSWORD MANAGER 47
- SET PASSWORD OPERATOR 48
- SET SWITCH CONSOLETIMER 49
- SET SYSTEM 50
- SET SYSTEM TEMPTHRESHOLD 51
- SHOW ASYN 52
- SHOW CONFIG 53
- SHOW DHCPBOOTP 54
- SHOW IP ROUTE 56
- SHOW SWITCH 57
- SHOW SWITCH LINECARD 58
- SHOW SYSTEM 59
- ADD SNTPSERVER IPADDRESS 61
- DELETE SNTPSERVER IPADDRESS 62
- DISABLE SNTP 63
- ENABLE SNTP 64
- RESET SNTP 65
- SET DATE 66
- SET SNTP 67
- SET TIME 68
- SHOW SNTP 69
- SHOW TIME 70
- SNMP Community Strings and 71
- Trap Commands 71
- ADD SNMP COMMUNITY 72
- CREATE SNMP COMMUNITY 74
- DELETE SNMP COMMUNITY 77
- DESTROY SNMP COMMUNITY 78
- DISABLE SNMP 79
- DISABLE SNMP COMMUNITY 81
- ENABLE SNMP 82
- ENABLE SNMP AUTHENTICATETRAP 83
- ENABLE SNMP COMMUNITY 84
- SET SNMP COMMUNITY 85
- SHOW SNMP 87
- Enhanced Stacking Commands 89
- ACCESS SWITCH 90
- SET SWITCH STACKMODE 93
- SHOW REMOTELIST 94
- Port Parameter Commands 95
- RESET SWITCH PORT 96
- SET SWITCH PORT 97
- SHOW SWITCH PORT 101
- Port Security Command 102
- SET SWITCH PORT SECURITYMODE 103
- Port Trunking Commands 106
- ADD SWITCH TRUNK 107
- CREATE SWITCH TRUNK 108
- DELETE SWITCH TRUNK 110
- DESTROY SWITCH TRUNK 111
- SET SWITCH TRUNK 112
- SHOW SWITCH TRUNK 113
- Port Mirroring Commands 114
- ADD SWITCH MIRROR 115
- CREATE SWITCH MIRROR 116
- DELETE SWITCH MIRROR 117
- DESTROY SWITCH MIRROR 118
- DISABLE SWITCH MIRROR 119
- ENABLE SWITCH MIRROR 120
- SET SWITCH MIRROR 121
- SHOW SWITCH MIRROR 122
- File System Commands 123
- CREATE CONFIG 125
- DELETE FILE 126
- SET CONFIG 128
- SHOW FILE 129
- File Download and Upload 130
- Commands 130
- STP Commands 139
- ACTIVATE STP 140
- DISABLE STP 141
- ENABLE STP 142
- RESET STP 143
- Chapter 13: STP Commands 144
- RSTP Commands 150
- ACTIVATE RSTP 151
- DISABLE RSTP 152
- ENABLE RSTP 153
- RESET RSTP 154
- SET RSTP 155
- Chapter 14: RSTP Commands 156
- SET RSTP PORT 158
- Chapter 15: MSTP Commands 164
- ADD MSTP 166
- CREATE MSTP 167
- DELETE MSTP 168
- DESTROY MSTP MSTI 169
- DISABLE MSTP 170
- ENABLE MSTP 171
- RESET MSTP 172
- SET MSTP 173
- SET MSTP CIST 176
- SET MSTP MSTI 177
- SET MSTP PORT 180
- ADD VLAN 186
- CREATE VLAN 189
- DELETE VLAN 193
- DESTROY VLAN 196
- RESET VLAN 197
- SET SWITCH MANAGEMENTVLAN 198
- SET SWITCH SWITCHMODE 199
- SET VLANMODE 200
- SHOW VLAN 202
- DISABLE GARP 204
- ENABLE GARP 205
- RESET GARP 206
- SET GARP PORT 207
- SET GARP TIMER 209
- SHOW GARP 211
- SHOW GARP COUNTER 212
- SHOW GARP DATABASE 214
- SHOW GARP GIP 215
- SHOW GARP MACHINE 216
- MAC Address Table Commands 217
- ADD SWITCH FDB 218
- DELETE SWITCH FDB 220
- SET SWITCH AGINGTIMER 221
- SHOW SWITCH FDB 222
- IGMP Snooping Commands 224
- SET IP IGMP 225
- SHOW IP IGMP 227
- Statistics Commands 228
- RESET SWITCH COUNTER 229
- RESET SWITCH LINECARD COUNTER 230
- RESET SWITCH PORT COUNTER 231
- SHOW SWITCH COUNTER 232
- SHOW SWITCH LINECARD COUNTER 233
- SHOW SWITCH PORT COUNTER 234
- Web Server Commands 235
- DISABLE HTTP SERVER 236
- ENABLE HTTP SERVER 237
- RESET HTTP SERVER 238
- SET HTTP SERVER 239
- Creating a Self 240
- Certificate 240
- Creating a CA 241
- SHOW HTTP SERVER 243
- Encryption Commands 244
- CREATE ENCO KEY 245
- DESTROY ENCO KEY 248
- SET ENCO KEY 249
- SHOW ENCO KEY 250
- ADD PKI CERTIFICATE 252
- CREATE PKI CERTIFICATE 254
- CREATE PKI ENROLLMENTREQUEST 256
- DELETE PKI CERTIFICATE 258
- PURGE PKI 259
- SET PKI CERTIFICATE 260
- SET PKI CERTSTORELIMIT 262
- SET SYSTEM DISTINGUISHEDNAME 263
- SHOW PKI 264
- SHOW PKI CERTIFICATE 265
- Secure Sockets Layer (SSL) 266
- SHOW SSL 268
- Secure Shell (SSH) Commands 269
- DISABLE SSH SERVER 270
- ENABLE SSH SERVER 271
- SET SSH SERVER 272
- Creating a 273
- Secure Shell 273
- Chapter 25: SSH Commands 274
- DISABLE PORTACCESS 277
- ENABLE PORTACCESS 278
- SET PORTACCESS 279
- SET PORTACCESS PORT ROLE 282
- SHOW PORTACCESS 285
- TACACS+ and RADIUS 286
- ADD RADIUSSERVER 287
- ADD TACACSSERVER 288
- DELETE RADIUSSERVER 289
- DELETE TACACSSERVER 290
- DISABLE AUTHENTICATION 291
- ENABLE AUTHENTICATION 292
- RESET AUTHENTICATION 293
- SET AUTHENTICATION 294
- SHOW AUTHENTICATION 296
Produits connexes et manuels pour Matériel informatique Allied-telesis AT-S60
(44 pages)
(38 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels