Allied-telesis AT-SBx81CFC960 Manuel d'utilisateur Page 212
- Page / 322
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 10: Verifying the Hardware Operations of the Chassis
212 Section II: Installing the Chassis
Using Local Management to Verify the Chassis
This section explains how to use the commands in the AlliedWare Plus
Operating System on the controller card to confirm the operations of the
chassis. The section has the following procedure:
“Starting a Local Management Session” on page 212
“Entering the AlliedWare Plus Operating System Commands” on
page 213
The initial management session of the switch must be a local
management session. For instructions on how to configure the chassis for
remote management with a Telnet or Secure Shell client, refer to the
Software Reference for SwitchBlade x8100 Series Switches.
Starting a Local
Management
Session
To start a local management session, perform the following procedure:
1. Connect the RJ-45 end of the management card included with the AT-
SBx81CFC960 Controller Fabric Card to the Console RS-232 port on
the front panel of the AT-SBx81CFC960 Controller Card, as shown in
Figure 150. If the chassis has two controller cards, you may use the
Console RS-232 port on either card to establish a local management
session with the chassis.
Figure 150. Connecting the Management Cable to the Console RS-232
Port
2. Connect the other end of the cable to an RS-232 port on a terminal or
personal computer with a terminal emulation program.
- Installation Guide 1
- Radiated Energy 3
- Industry Canada 3
- Translated Safety Statements 4
- Contents 5
- List of Tables 14
- ™ feature 16
- Contacting Allied Telesis 18
- Hardware Overview 19
- Chassis and Power Supplies 21
- Introduction 22
- Figure 3. Fan Module 23
- AT-SBxFAN06 Module Cooling 23
- AT-SBx8106 Chassis 24
- Slots for the Power Supplies 27
- AT-SBxPWRSYS1 AC Power Supply 28
- AT-SBxPWRPOE1 Power Supply 30
- AT-SBxFAN06 Module 34
- AT-SBx81GT24 Line Card 39
- AT-SBx81GT40 Line Card 41
- AT-SBx81GP24 PoE Line Card 44
- AT-SBx81GS24a SFP Line Card 47
- AT-SBx81XS6 SFP+ Line Card 49
- AT-SBx81XS16 SFP+ Line Card 51
- Distance 53
- Requirements 54
- Automatic MDIX 55
- Detection 55
- Powered Device 56
- Chapter 3 59
- Hardware Components 60
- Guidelines 62
- Dual Controller Cards 64
- SYS Status LEDs 66
- SBx Linecard Status LEDs 69
- SFP+ Slots 70
- Console (RS-232) Port 72
- NET MGMT 73
- USB Port 75
- Reset Button 76
- Installing the Chassis 79
- Safety Precautions and Site 81
- Reviewing Safety Precautions 82
- Chapter 5 89
- Required Tools and Material 90
- Preparing the Equipment Rack 91
- 190.0 mm (7.5“) 92
- 152.4 mm (6”0) 92
- 342.4 mm (13.5”) 92
- Removing the Rubber Feet 96
- 3. Turn the chassis over 97
- “Dim X” “Dim X” “Dim X” 99
- Removing the Shipping Brace 104
- Installing the Power Supplies 107
- Chapter 7 127
- INCORRECT 129
- Controller Fabric Card 134
- Chapter 8 143
- Cables to the AT 145
- SBx81GT40 Line 145
- Connecting 145
- Powering On the Chassis 171
- Verifying the Installation 172
- Power Supply 174
- Connecting the 184
- Grounding Wire 184
- DC Power Wires 195
- Angle Terminals 195
- Connecting Bare 201
- Chapter 10 209
- Starting a Local 212
- Management 212
- Entering the 213
- AlliedWare Plus 213
- Operating System 213
- Commands 213
- Troubleshooting 215
- AT-SBxPWRSYS1 DC Power Supply 217
- Chapter 11: Troubleshooting 218
- Ethernet Line Cards 219
- Twisted Pair Ports 221
- Power Over Ethernet 223
- AT-SBxFAN06 Fan Module 227
- Replacing Modules 231
- Supplies 232
- Chapter 12: Replacing Modules 234
- Figure 157 on page 236 235
- 165 on page 244 243
- Figure 168 on page 247 246
- Replacing Ethernet Line Cards 248
- Removing the 253
- AT-SBxFAN06 253
- Fan Module 253
- Connector 254
- Installing a New 256
- Chapter 13 259
- Before You Begin 260
- Switches 265
- Section III 267
- VCStack Plus Overview 269
- Overview 270
- One Controller 273
- Card Per Chassis 273
- Two Controller 274
- Cards Per 274
- VCStack Plus Feature License 276
- Optional Feature Licenses 277
- Chassis ID Numbers 278
- Priority Numbers 279
- Stacking Guidelines 281
- Building a Stack 283
- Chapter 15: Building a Stack 286
- Enabling the Stacking Feature 289
- Setting the ID Number 293
- Setting the Priority Number 297
- Powering Off the Chassis 298
- Powering On the Stack 303
- Powering On the 304
- Monitoring the 304
- Sequence 304
- Verifying the Stack 307
- Troubleshooting the Stack 310
- Technical Specifications 313
- Environmental Specifications 315
- Power Specifications 316
- PoE Mode 318
- Port Pinouts 319
- Transceivers 321
Produits connexes et manuels pour Matériel informatique Allied-telesis AT-SBx81CFC960
(322 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.074 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels