Allied-telesis SwitchBlade x8112 Manuel d'utilisateur

613-001716 Rev. DSwitchBlade x8112Layer 3+ Chassis Switch AT-SBx8112 Chassis AT-SBx81GT24 Line Card AT-SBx81GT40 Line Card AT-SBx81GP24 PoE Line C

List of Figures10Figure 50: Removing the Blank Slot Cover from Power Supply Slot A...

Chapter 4: Installing the Power Supplies1007. Lower the locking handle of the power supply module to secure the module in the slot, as shown in Figure

SwitchBlade x8112 Chassis Switch Installation Guide101Installing the AT-SBxPWRSYS1 DC System Power SupplyThis section contains the installation proced

Chapter 4: Installing the Power Supplies102Figure 56. Removing the Blank Slot Cover from Power Supply Slot C3. Remove the power supply from the shippi

SwitchBlade x8112 Chassis Switch Installation Guide103Figure 57. Items Included with the AT-SBxPWRSYS1 DC Power Supply ModuleNoteStore the packaging m

Chapter 4: Installing the Power Supplies104Figure 58. Loosening the Handle locking Screw on the AT-SBxPWRPOE1 DC System Power Supply5. Raise the locki

SwitchBlade x8112 Chassis Switch Installation Guide105Figure 60. Inserting the AT-SBxPWRSYS1 DC System Power Supply

Chapter 4: Installing the Power Supplies1067. Lower the locking handle of the power supply module to secure the module in the slot, as shown in Figure

107Chapter 5Installing the AT-SBx81CFC400 Control Card and Ethernet Line CardsThis chapter describes how to install the control and Ethernet line card

Chapter 5: Installing the AT-SBx81CFC400 Control Card and Ethernet Line Cards108Guidelines to Handling the Controller and Line CardsPlease observe the

SwitchBlade x8112 Chassis Switch Installation Guide109Figure 62. Aligning Card in SlotCORRECTINCORRECTINCORRECT

SwitchBlade x8112 Chassis Switch Installation Guide11Figure 110: Attaching the Power Wires to the Straight Terminal Lugs...

Chapter 5: Installing the AT-SBx81CFC400 Control Card and Ethernet Line Cards110Installing the AT-SBx81CFC400 Controller Fabric CardThis section conta

SwitchBlade x8112 Chassis Switch Installation Guide111Figure 64. Items Included with the AT-SBx81CFC400 Controller CardNoteStore the packaging materia

Chapter 5: Installing the AT-SBx81CFC400 Control Card and Ethernet Line Cards112Figure 66. Opening the Locking Handles on the AT-SBx81CFC400 Controlle

SwitchBlade x8112 Chassis Switch Installation Guide113Figure 68. Aligning the AT-SBx81CFC400 Card in the Chassis Slot7. Carefully slide the card into

Chapter 5: Installing the AT-SBx81CFC400 Control Card and Ethernet Line Cards114Figure 69. Closing the Locking Levers on the AT-SBx81CFC400 Controller

SwitchBlade x8112 Chassis Switch Installation Guide115Figure 70. Tightening the Thumb Screws on the AT-SBx81CFC400 Card10. Tighten the screws with a #

Chapter 5: Installing the AT-SBx81CFC400 Control Card and Ethernet Line Cards116Installing the Ethernet Line CardsThis section contains the installati

SwitchBlade x8112 Chassis Switch Installation Guide117Figure 72. Removing an Ethernet Line Card from the Anti-static Bag4. Align the line card with th

Chapter 5: Installing the AT-SBx81CFC400 Control Card and Ethernet Line Cards118CautionIt is important to keep the card level with the chassis as you

SwitchBlade x8112 Chassis Switch Installation Guide119Figure 75. Tightening the Thumb Screws on an Ethernet Line Card8. Tighten the two screws with a

List of Figures12

Chapter 5: Installing the AT-SBx81CFC400 Control Card and Ethernet Line Cards120Installing the Blank Slot CoversAfter installing the AT-SBx81CFC400 Co

SwitchBlade x8112 Chassis Switch Installation Guide121Figure 77. Tightening the Thumbscrews on a Blank Slot Cover3. Tighten the two screws with a # 2

Chapter 5: Installing the AT-SBx81CFC400 Control Card and Ethernet Line Cards122

123Chapter 6Installing the Transceivers and Cabling the PortsThis chapter describes how to install the fiber optic transceivers and attach the cables

Chapter 6: Installing the Transceivers and Cabling the Ports124Cabling Guidelines for the Twisted Pair Ports on the AT-SBx81GT24, AT-SBx81GT40, and AT

SwitchBlade x8112 Chassis Switch Installation Guide125 The default wiring configuration of the ports is automatic MDIX detection, which configures th

Chapter 6: Installing the Transceivers and Cabling the Ports126Figure 79. Connecting Cables to Ports on the AT-SBx81GT40 Line CardRelease TabConnectin

SwitchBlade x8112 Chassis Switch Installation Guide127Guidelines to Installing SFP and SFP+ TransceiversPlease review the following guidelines before

Chapter 6: Installing the Transceivers and Cabling the Ports128Installing SFP Transceivers in the AT-SBx81GS24a Line CardPlease review the information

SwitchBlade x8112 Chassis Switch Installation Guide1293. To install the transceiver in an SFP slot on the top row of the line card, orient the transce

13Table 1. Twisted Pair Cable for the AT-SBx81GT24 and AT-SBx81GT40 Line Cards ...33Table 2. Twi

Chapter 6: Installing the Transceivers and Cabling the Ports130NoteIf you are ready to attach the fiber optic cable to the transceiver, continue with

SwitchBlade x8112 Chassis Switch Installation Guide1316. Connect the fiber optic cable to the port on the transceiver, as shown in Figure 84. The conn

Chapter 6: Installing the Transceivers and Cabling the Ports132Installing SFP+ Transceivers in the AT-SBx81XS6 Line CardPlease review the information

SwitchBlade x8112 Chassis Switch Installation Guide133Figure 86. Handle on SFP+ Transceiver3. Slide the transceiver into the slot until it clicks into

Chapter 6: Installing the Transceivers and Cabling the Ports1344. Remove the protective cover from the SFP transceiver, as shown in Figure 88.Figure 8

SwitchBlade x8112 Chassis Switch Installation Guide1355. Connect the fiber optic cable to the port on the transceiver, as shown in Figure 89. The conn

Chapter 6: Installing the Transceivers and Cabling the Ports136Installing AT-SP10TW Cables in the AT-SBx81XS6 Line CardThis procedure explains how to

SwitchBlade x8112 Chassis Switch Installation Guide137NoteDo not remove the dust plug from the SFP+ slot if you are not installing the transceiver at

Chapter 6: Installing the Transceivers and Cabling the Ports1384. Install the other end of the cable into an SFP+ slot on another network device.5. Re

SwitchBlade x8112 Chassis Switch Installation Guide139Cabling the NET MGMT Port on the AT-SBx81CFC400 CardThe controller card must have access to your

List of Tables14

Chapter 6: Installing the Transceivers and Cabling the Ports140This setting is appropriate for port if it is connected to a network device that also s

141Chapter 7Powering On the ChassisThis chapter describes how to power on the chassis and monitor the initialization process. The chapter contains the

Chapter 7: Powering On the Chassis142Verifying the InstallationPlease perform the following procedure before powering on the chassis:1. Verify that th

SwitchBlade x8112 Chassis Switch Installation Guide143Powering On the AT-SBxPWRSYS1 AC System Power SupplyThe procedure in this section explains how t

Chapter 7: Powering On the Chassis144If there are two system power supplies, you may power on either supply first. In the illustration in Figure 94 an

SwitchBlade x8112 Chassis Switch Installation Guide145Figure 95. Securing the Power Cord for the AT-SBxPWRSYS1 AC Power Supply to an Anchor4. Connect

Chapter 7: Powering On the Chassis146Powering On the AT-SBxPWRPOE1 Power SupplyIf you have not already installed the AT-SBxPWRPOE1 Power Supplies, ref

SwitchBlade x8112 Chassis Switch Installation Guide1473. Use the twist tie that comes with the power supply to secure the cord to an anchor on the cha

Chapter 7: Powering On the Chassis148Figure 98. Dress and Secure AC Power Cords6. Go to “Monitoring the Initialization Process” on page 175.

SwitchBlade x8112 Chassis Switch Installation Guide149Powering On the AT-SBxPWRSYS1 DC System Power SupplyThis section contains instructions on how to

15PrefaceThis guide contains the hardware installation instructions for the Layer 3+ SwitchBlade x8112 Chassis Switch. The preface contains the follow

Chapter 7: Powering On the Chassis150The components of the power supply are identified in Figure 99.Figure 99. Components of the AT-SBxPWRSYS1 DC Powe

SwitchBlade x8112 Chassis Switch Installation Guide151Choosing aMethod forAttaching theGrounding WireYou may attach the grounding wire to the power su

Chapter 7: Powering On the Chassis1523. Use an 8 mm wrench to remove the grounding post nut and washer, shown in Figure 103, from the power supply.Fig

SwitchBlade x8112 Chassis Switch Installation Guide153Figure 104. Installing the Grounding Wire5. Connect the other end of the grounding wire to the b

Chapter 7: Powering On the Chassis154Connecting theGrounding Wirewith Bare WireTo attach the grounding wire to the power supply with bare wire, perfor

SwitchBlade x8112 Chassis Switch Installation Guide1554. Secure the wire with the nut and washer removed in step 2, and an 8 mm wrench, as shown in Fi

Chapter 7: Powering On the Chassis156Choosing aMethod forAttaching thePower WiresThe AT-SBxPWRSYS1 DC Power Supply comes with the two sets of power wi

SwitchBlade x8112 Chassis Switch Installation Guide157Figure 109. Stripping the Power WiresNoteYou must use stranded wires with the terminal lugs. You

Chapter 7: Powering On the Chassis158Figure 111. On/Off Switch on the AT-SBxPWRSYS1 DC Power Supply4. Use a #1 Phillips-head screwdriver to loosen the

SwitchBlade x8112 Chassis Switch Installation Guide159Figure 112. Opening the Plastic Cover5. Use a #3 Phillips-head screwdriver to remove the two scr

Preface16Safety Symbols Used in this DocumentThis document uses the following conventions.NoteNotes provide additional information.CautionCautions inf

Chapter 7: Powering On the Chassis160Figure 113. Removing the Terminal Screws6. With a #3 Phillips-head screwdriver, connect the positive (+) power le

SwitchBlade x8112 Chassis Switch Installation Guide161Figure 114. Connecting the Positive (+) Power Wire with a Straight Terminal7. With a #3 Phillips

Chapter 7: Powering On the Chassis162Figure 115. Connecting the Negative (-) Power Wire with a Straight TerminalWarningCheck to see if there are any e

SwitchBlade x8112 Chassis Switch Installation Guide163Figure 116. Closing the Plastic Cover over the Terminal ConnectorsCautionDo not over tighten the

Chapter 7: Powering On the Chassis164Figure 117. Tightening the Handle Locking Screw10. Before attaching the power wires from the power supply to the

SwitchBlade x8112 Chassis Switch Installation Guide165Connecting theDC Power Wireswith the RightAngle TerminalsTo connect the DC power wires to the po

Chapter 7: Powering On the Chassis1664. Using a #1 Phillips-head screwdriver, remove the two screws that secure the plastic cover over the positive an

SwitchBlade x8112 Chassis Switch Installation Guide167Figure 121. Removing the Terminal Screws6. With a #3 Phillips-head screwdriver, connect the posi

Chapter 7: Powering On the Chassis168Figure 122. Connecting the Positive (+) Power Wire with a Right Angle Terminal7. With a #3 Phillips-head screwdri

SwitchBlade x8112 Chassis Switch Installation Guide169Figure 123. Connecting the Negative (-) Power Wire with a Right Angle TerminalWarningCheck to se

SwitchBlade x8112 Chassis Switch Installation Guide17Contacting Allied TelesisIf you need assistance with this product, you may contact Allied Telesis

Chapter 7: Powering On the Chassis170Figure 124. Tightening the Handle Locking Screw9. Before attaching the power wires from the power supply to the c

SwitchBlade x8112 Chassis Switch Installation Guide171Connecting BareDC Power WiresTo attach bare lead wires to the positive and negative terminals on

Chapter 7: Powering On the Chassis172Figure 126. Connecting the Positive Wire With Bare Wire5. Wrap the negative lead wire clockwise around the remain

SwitchBlade x8112 Chassis Switch Installation Guide173Figure 127. Connecting the Negative Lead Wire with Bare WireAllied Telesis recommends tightening

Chapter 7: Powering On the Chassis1747. With a #2 Phillips-head screwdriver, tighten the handle locking screw to secure the power supply to the chassi

SwitchBlade x8112 Chassis Switch Installation Guide175Monitoring the Initialization ProcessThe line and controller cards perform an initialization pro

Chapter 7: Powering On the Chassis176Figure 128. Switch Initialization MessagesVerifying release... OKBooting...Starting base/first... [ OK ]Mounting

SwitchBlade x8112 Chassis Switch Installation Guide177Figure 129. Switch Initialization Messages (Continued)auth, bgpd, cntrd, epsr, exfx, hostd, hsli

Chapter 7: Powering On the Chassis178

179Chapter 8Verifying the Hardware Operations of the ChassisThis chapter describes how to verify the operations of the chassis. The chapter contains t

Preface18

Chapter 8: Verifying the Hardware Operations of the Chassis180Using the LEDs to Verify the ChassisAfter powering on the chassis for the first time and

SwitchBlade x8112 Chassis Switch Installation Guide181prevents them from completing the initialization process. Power off the chassis and replace the

Chapter 8: Verifying the Hardware Operations of the Chassis182Using Local Management to Verify the ChassisThis section explains how to use the command

SwitchBlade x8112 Chassis Switch Installation Guide1832. Connect the other end of the cable to an RS-232 port on a terminal or personal computer with

Chapter 8: Verifying the Hardware Operations of the Chassis184Figure 131. SHOW VERSION Command2. Compare the version number displayed by the SHOW VERS

SwitchBlade x8112 Chassis Switch Installation Guide1855. To display the states of the individual ports on the Ethernet line cards, use the SHOW INTERF

Chapter 8: Verifying the Hardware Operations of the Chassis186

187Chapter 9TroubleshootingThis chapter contains information on how to troubleshoot the SwitchBlade x8112 product.NoteIf you are unable to resolve a h

Chapter 9: Troubleshooting188AT-SBxPWRSYS1 and AT-SBxPWRPOE1 AC Power SuppliesA power supply is operating normally when its AC and DC LEDs are solid g

SwitchBlade x8112 Chassis Switch Installation Guide189AT-SBxPWRSYS1 DC System Power SupplyIf you suspect a problem with the DC power supply, examine i

19Chapter 1OverviewThis chapter describes the Layer 3+ SwitchBlade x8112 Chassis Switch in the following sections: “Introduction” on page 20 “AT-SBx

Chapter 9: Troubleshooting190software version on the control card, refer to “Using Local Management to Verify the Chassis” on page 182 and “AlliedWare

SwitchBlade x8112 Chassis Switch Installation Guide191Ethernet Line CardsA quick and easy way to check the overall heath of the Ethernet line cards in

Chapter 9: Troubleshooting192 Try installing the card in a different slot. If it works in the new slot, the problem is with the previous slot. Try i

SwitchBlade x8112 Chassis Switch Installation Guide193Twisted Pair PortsThe ports on the AT-SBx81GT24 and AT-SBx81GP24 Line Cards have L/A LEDs that a

Chapter 9: Troubleshooting194 The default duplex mode setting for the ports is Auto-Negotiation. This setting is appropriate for ports connected to n

SwitchBlade x8112 Chassis Switch Installation Guide195Power Over EthernetThis section applies only to the AT-SBx81GP24 Line Card. Each port has two LE

Chapter 9: Troubleshooting196 Use the SHOW POE CARD command to determine whether the switch has reach its maximum power budget. Try connecting the P

SwitchBlade x8112 Chassis Switch Installation Guide197Fiber Optic TransceiversThe L/A LEDs on the AT-SBx81GS24a and AT-SBx81XS6 Line Cards are solid o

Chapter 9: Troubleshooting198AT-SBx81CFC400 Controller Fabric CardThe consequences of a controller card failure on the operations of the Ethernet line

SwitchBlade x8112 Chassis Switch Installation Guide199AT-SBxFAN12 Fan ModuleThe AT-SBxFAN12 Fan Module is operating correctly when the POWER LED on th

Copyright  2013 Allied Telesis, Inc.All rights reserved. No part of this publication may be reproduced without prior written permission from Allied T

Chapter 1: Overview20IntroductionThe SwitchBlade x8112 product is a modular Layer 3+ Ethernet switch. The main components are the AT-SBx8112 Chassis,

Chapter 9: Troubleshooting200Local (Out-of-Band) Management SessionIf you are unable to establish a local (out-of-band) management session with the sw

SwitchBlade x8112 Chassis Switch Installation Guide201Power Supply Interfaces (Opto-couplers)The two power supply interfaces in the lower right corner

Chapter 9: Troubleshooting202

203Chapter 10Replacing ModulesThis chapter contains procedures on how to remove modules from the unit. The chapter has the following sections: “Repla

Chapter 10: Replacing Modules204Replacing AT-SBxPWRSYS1 AC and AT-SBxPWRPOE1 Power SuppliesThis section contains the procedure for removing AT-SBxPWRS

SwitchBlade x8112 Chassis Switch Installation Guide2052. Lift the locking hand on the power supply. Refer to Figure 134.Figure 134. Lifting the Lockin

Chapter 10: Replacing Modules206Figure 135. Removing the Power Supply from the Chassis4. Do one of the following: To install a new power supply, refe

SwitchBlade x8112 Chassis Switch Installation Guide207Figure 136. Installing a Blank Power Supply Slot Cover6. Lower the locking handle to secure the

Chapter 10: Replacing Modules208Figure 137. Lowering the Locking Handle on the Power Supply Slot Cover

SwitchBlade x8112 Chassis Switch Installation Guide209Replacing the AT-SBxPWRSYS1 DC Power SupplyTo remove an AT-SBxPWRSYS1 DC Power Supply from the c

SwitchBlade x8112 Chassis Switch Installation Guide21Figure 3. Ethernet Line Cards and Controller Card (Continued)Figure 4 illustrates the power suppl

Chapter 10: Replacing Modules210NoteIf the power wires are connected to the terminal block with the right angle terminals, go to step 5.4. Use a #1 sc

SwitchBlade x8112 Chassis Switch Installation Guide211Figure 140. Removing the Negative Lead Wire6. Use a #3 screwdriver to remove the positive (+) le

Chapter 10: Replacing Modules212Figure 141. Removing the Positive Lead Wire from the Terminal Block7. Reinstall the two screws on the negative (-) and

SwitchBlade x8112 Chassis Switch Installation Guide213Figure 142. Reinstalling the Screws on the Positive and Negative Terminals8. Slide the plastic c

Chapter 10: Replacing Modules214Figure 143. Closing the Plastic Cover9. Use an 8 mm wrench to remove the grounding wire from the grounding post. Refer

SwitchBlade x8112 Chassis Switch Installation Guide215Figure 144. Removing the Grounding Wire10. Reinstall the nut and washer on the grounding post. R

Chapter 10: Replacing Modules216Figure 145. Reinstalling the Nut and Washer on the Grounding Post11. Lift the locking handle and slide the power suppl

SwitchBlade x8112 Chassis Switch Installation Guide217Figure 146. Lifting the Locking Handle and Removing the Power Supply12. Do one of the following:

Chapter 10: Replacing Modules218Figure 147. Installing a Blank Power Supply Slot Cover14. Lower the locking handle to secure the slot cover to the slo

SwitchBlade x8112 Chassis Switch Installation Guide219Figure 148. Lowering the Locking Handle on the Power Supply Slot Cover

Chapter 1: Overview22Figure 5 illustrates the fan module.Figure 5. Fan ModuleAT-SBxFAN12 Module Cooling module for the chassis.

Chapter 10: Replacing Modules220Replacing Ethernet Line CardsThis section contains the procedure for replacing Ethernet line cards from the chassis.No

SwitchBlade x8112 Chassis Switch Installation Guide221instructions, refer to “Installing the Blank Slot Covers” on page 120. If you do not plan to im

Chapter 10: Replacing Modules222Replacing the AT-SBx81CFC400 Controller Fabric CardThis section contains the procedure for replacing a controller card

SwitchBlade x8112 Chassis Switch Installation Guide223NoteYou should not replace a controller card in a chassis that has two controller cards while th

Chapter 10: Replacing Modules224Replacing the AT-SBxFAN12 Fan ModuleThis section contains the procedures for replacing the AT-SBxFAN12 Fan Module, loc

SwitchBlade x8112 Chassis Switch Installation Guide225Figure 149. Loosening the Screw on the AT-SBxFAN12 Fan Module3. Carefully pull on the handle to

Chapter 10: Replacing Modules226Figure 150. Loosening the AT-SBxFAN12 Fan Module from the Backplane Connector4. Slowly pull out the module 51 mm (2 in

SwitchBlade x8112 Chassis Switch Installation Guide227Figure 151. Withdrawing the AT-SBxFAN12 Fan Module 51 mm (2 In.) from the Chassis5. Wait ten sec

Chapter 10: Replacing Modules228Figure 152. Removing the AT-SBxFAN12 Fan Module from the ChassisInstalling a NewAT-SBxFAN12Fan ModuleThis procedure as

SwitchBlade x8112 Chassis Switch Installation Guide229Figure 153. Installing a New AT-SBxFAN12 Fan Module2. When you feel the fan module make contact

SwitchBlade x8112 Chassis Switch Installation Guide23AT-SBx8112 ChassisThe AT-SBx8112 Chassis is a 7RU unit. It has slots for ten Ethernet line cards,

Chapter 10: Replacing Modules230Figure 154. Securing the AT-SBxFAN12 Fan Module on the Backplane Connector3. With a #2 Phillips-head screwdriver, tigh

SwitchBlade x8112 Chassis Switch Installation Guide231Figure 155. Tightening the Screw on the AT-SBxFAN12 Fan Module4. Reconnect any network cables yo

Chapter 10: Replacing Modules232

233Appendix ATechnical SpecificationsPhysical SpecificationsDimensions (W x D x H)Weight (Kilograms)Table 21. Product DimensionsAT-SBx8112 Chassis 4

Appendix A: Technical Specifications234AT-SBx81GS24a SFP Line Card 1.06 kg (2.34 lb)AT-SBx81XS6 SFP+ Line Card 1.06 kg (2.34 lb)AT-SBx81CFC400 Control

SwitchBlade x8112 Chassis Switch Installation Guide235Environmental SpecificationsNoteThe acoustic noise was measured at 40° C with the following prod

Appendix A: Technical Specifications236Power SpecificationsAC Voltage, Frequency Requirements (Volts, Hertz)DC Voltage RequirementsTypical power savin

SwitchBlade x8112 Chassis Switch Installation Guide237Maximum power supply efficiency (based on 100V input voltage)Heat dissipation (British Thermal U

Appendix A: Technical Specifications238PoE ModeSafety and Electromagnetic Emissions CertificationsSafety and Electromagnetic Emissions:Table 32. Ava

SwitchBlade x8112 Chassis Switch Installation Guide239Port PinoutsThis section lists the port pinouts for the AT-SBx81GT24, AT-SBx81GT40, and AT-SBx81

Chapter 1: Overview24Figure 7. Rear View of the AT-SBx8112 ChassisFigure 8 is an example of a fully populated chassis.Figure 8. AT-SBx8112 Chassis wit

Appendix A: Technical Specifications240Table 37 lists the port pin signals when a 10/100/1000Base-T port is operating at 1000 Mbps.Table 37. 1000Bas

SwitchBlade x8112 Chassis Switch Installation Guide25Ethernet Lineand ControllerCards SlotsThe chassis has slots for ten Ethernet line cards and two A

Chapter 1: Overview26modules to increase the available PoE power for the powered devices or to add power redundancy. For more information, refer to “P

SwitchBlade x8112 Chassis Switch Installation Guide27AT-SBx81GT24 Line CardThe AT-SBx81GT24 Line Card, shown in Figure 11, is a Gigabit Ethernet switc

Chapter 1: Overview28AT-SBx81GT40 Line CardThe AT-SBx81GT40 Line Card, shown in Figure 12, is a Gigabit Ethernet switch.Figure 12. AT-SBx81GT40 Line C

SwitchBlade x8112 Chassis Switch Installation Guide29AT-SBx81GP24 PoE Line CardThe AT-SBx81GP24 PoE Line Card, shown in Figure 13, is a Gigabit Ethern

3Electrical Safety and Emissions StandardsThis product meets the following standardsEMI/RFI Emissions: FCC Class A, EN55022 Class A, EN61000-3-2, EN61

Chapter 1: Overview30AT-SBx81GS24a SFP Line CardThe AT-SBx81GS24a SFP Line Card, shown in Figure 14, is a Gigabit Ethernet switch.Figure 14. AT-SBx81G

SwitchBlade x8112 Chassis Switch Installation Guide31AT-SBx81XS6 SFP+ Line CardThe AT-SBx81XS6 Line Card, shown in Figure 15, is a 10 Gigabit Ethernet

Chapter 1: Overview3210/100/1000Base-T Twisted Pair PortsThis section applies to the 10/100/1000Base-T ports on the AT-SBx81GT24, AT-SBx81GT40, and AT

SwitchBlade x8112 Chassis Switch Installation Guide33MaximumDistanceThe ports have a maximum operating distance of 100 meters (328 feet).CableRequirem

Chapter 1: Overview34Automatic MDIXDetectionThe 10/100/1000 Mbps twisted-pair ports on the AT-SBx81GT24, AT-SBx81GT40, and AT-SBx81GP24 Line Cards are

SwitchBlade x8112 Chassis Switch Installation Guide35Power over Ethernet on the AT-SBx81GP24 Line CardThis section applies to the AT-SBx81GP24 PoE Lin

Chapter 1: Overview36Power Budgeting The power for PoE on the ports on the AT-SBx81GP24 Line Card is provided by the AT-SBxPWRPOE1 Power Supply. It ca

SwitchBlade x8112 Chassis Switch Installation Guide37PDs that comply with the IEEE 802.3af and 802.3at standards typically support both power delivery

Chapter 1: Overview38Port LEDs on the Ethernet Line CardsThe following sections define the port LEDs on the Ethernet line cards.AT-SBx81GT24Line CardE

SwitchBlade x8112 Chassis Switch Installation Guide39AT-SBx81GT40Line CardThe LEDs for a port on the AT-SBx81GT40 Line Card are found on the RJ point

SwitchBlade x8112 Chassis Switch Installation Guide4Translated Safety StatementsImportant: The  indicates that a translation of the safety statement

Chapter 1: Overview40Figure 18. Port LEDs on an RJ Point 5 Cable Connector for the AT-SBx81GT40 Line CardTable 6. Port LEDs on the AT-SBx81GT40 Line

SwitchBlade x8112 Chassis Switch Installation Guide41AT-SBx81GP24Line CardEach port on the AT-SBx81GP24 PoE Line Card has two LEDs. The LEDs are shown

Chapter 1: Overview42AT-SBx81GS24aLine CardThe SFP slots on the AT-SBx81GS24a SFP Line Card have one LED each, as shown in Figure 20 and described in

SwitchBlade x8112 Chassis Switch Installation Guide43AT-SBx81XS6Line CardThe AT-SBx81XS6 Line Card has one LED for each SFP+ slot. The LED is shown in

Chapter 1: Overview44AT-SBx81CFC400 Controller Fabric CardThe AT-SBx81CFC400 Controller Fabric Card has three primary functions: Chassis Management —

SwitchBlade x8112 Chassis Switch Installation Guide45The components on the card are identified in Figure 22.Figure 22. AT-SBx81CFC400 Controller Fabri

Chapter 1: Overview46Table 10. SYS (System) Status LEDsLED State DescriptionCFCSolid Green Indicates that the AT-SBx81CFC400 Controller Fabric Card

SwitchBlade x8112 Chassis Switch Installation Guide47SBx STATUSLEDsThe SBx LINECARD STATUS LEDs display general status information about the Ethernet

Chapter 1: Overview48eco-friendlyButtonYou may use the eco-friendly button on the controller card to turn the LEDs on or off. You may turn off the LED

SwitchBlade x8112 Chassis Switch Installation Guide49NoteThe available bandwidth across the backplane of the chassis is reduced from 80 to 40 Gbps per

5Preface ...

Chapter 1: Overview50The NET MGMT port has a standard RJ-45 8-pin connector and operates at 10, 100, or 1000 Mbps in either half- or full-duplex mode.

SwitchBlade x8112 Chassis Switch Installation Guide51The wiring configuration of the NET MGMT port is set automatically with automatic MDIX detection.

Chapter 1: Overview52 Boot the AlliedWare Plus Operating System and master configuration file from flash drive.The port is compatible with USB v1.0 a

SwitchBlade x8112 Chassis Switch Installation Guide53AT-SBxPWRSYS1 Power SupplyThe AT-SBxPWRSYS1 Power Supply, shown in Figure 23, is the power supply

Chapter 1: Overview54DCSolid Green The power supply is providing DC power that is within the normal operating range.Off The power supply is not genera

SwitchBlade x8112 Chassis Switch Installation Guide55AT-SBxPWRPOE1 Power SupplyThe AT-SBxPWRPOE1 Power Supply, shown in Figure 24, provides the PoE po

Chapter 1: Overview56Table 15. AT-SBxPWRPOE1 Power Supply LEDsLED State DescriptionACSolid Green The power supply is receiving AC power that is with

SwitchBlade x8112 Chassis Switch Installation Guide57AT-SBxPWRSYS1 DC Power SupplyThe AT-SBxPWRSYS1 DC Power Supply, shown in Figure 25, is a DC versi

Chapter 1: Overview58NoteTo avoid installing both AC and DC power supplies in the same chassis, you should use the AT-SBxPWRSYS1 AC Power Supply, and

SwitchBlade x8112 Chassis Switch Installation Guide59AT-SBxFAN12 ModuleThe AT-SBxFAN12 Module, shown in Figure 26, is the cooling unit for the chassis

Contents6AT-SBxPWRSYS1 DC Power Supply... 5

Chapter 1: Overview60Power Supply Interfaces (Opto-couplers)The chassis has two power supply interfaces, also referred to as opto-couplers, in the low

SwitchBlade x8112 Chassis Switch Installation Guide61AlliedWare Plus Software Releases for the Hardware ComponentsTable 19 lists the releases of the A

Chapter 1: Overview62

63Chapter 2Safety Precautions and Site RequirementsThis chapter contains the safety precautions and guidelines for selecting a site for the chassis. T

Chapter 2: Safety Precautions and Site Requirements64Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to in

SwitchBlade x8112 Chassis Switch Installation Guide65NotePluggable Equipment. The socket outlet shall be installed near the equipment and shall be eas

Chapter 2: Safety Precautions and Site Requirements66WarningMounting of the equipment in the rack should be such that a hazardous condition is not cre

SwitchBlade x8112 Chassis Switch Installation Guide67WarningTo reduce the risk of electric shock, the PoE ports on this product must not connect to ca

Chapter 2: Safety Precautions and Site Requirements68Selecting a Site for the SwitchBlade x8112Please observe the following site requirements for the

SwitchBlade x8112 Chassis Switch Installation Guide69Figure 28. 100 - 125 VAC 125 V NEMA 5-20 Plug and Receptacle

SwitchBlade x8112 Chassis Switch Installation Guide7Using the Console Port to Monitor the Initialization Process ...

Chapter 2: Safety Precautions and Site Requirements70Installation Tools and MaterialThis section lists the tools and material you need to supply to in

71Chapter 3Installing the Chassis in an Equipment RackThis chapter describes how to install the AT-SBx8112 Chassis in an equipment rack. This chapter

Chapter 3: Installing the Chassis in an Equipment Rack72Required Tools and MaterialHere is a list of the tools and material you need to perform the in

SwitchBlade x8112 Chassis Switch Installation Guide73Preparing the Equipment RackThis section explains how to prepare the equipment rack for the chass

Chapter 3: Installing the Chassis in an Equipment Rack74Figure 29. Reserving Vertical Rack Space

SwitchBlade x8112 Chassis Switch Installation Guide753. Identify the lowest 1/2” screw hole pattern on the rack mounting rails within the space reserv

Chapter 3: Installing the Chassis in an Equipment Rack76Unpacking the AT-SBx8112 ChassisTo unpack the AT-SBx8112 Chassis, perform the following proced

SwitchBlade x8112 Chassis Switch Installation Guide77Figure 32. Components of the AT-SBx8112 Chassis (Continued)Two equipment rack brackets pre-instal

Chapter 3: Installing the Chassis in an Equipment Rack78Adjusting the Equipment Rack BracketsYou may set the position of the chassis relative to the f

SwitchBlade x8112 Chassis Switch Installation Guide79Figure 33. Rack Mounting Bracket LocationsFigure 34. Rack Bracket Locations for Reverse Position

Contents8

Chapter 3: Installing the Chassis in an Equipment Rack80Installing the AT-SBx8112 Chassis in the Equipment RackThe procedure in this section explains

SwitchBlade x8112 Chassis Switch Installation Guide812. Lift the AT-SBx8112 Chassis into the equipment rack and set the bottom of the equipment rack b

Chapter 3: Installing the Chassis in an Equipment Rack82Figure 36. Installing the Rack Mount Screws5. Tighten all eight screws to secure the chassis t

SwitchBlade x8112 Chassis Switch Installation Guide83Removing the Shipping BraceNow that the chassis is installed in the equipment rack, you may remov

Chapter 3: Installing the Chassis in an Equipment Rack84Installing the Chassis Grounding LugThis procedure explains how to connect a grounding wire to

SwitchBlade x8112 Chassis Switch Installation Guide853. Insert one end of the grounding wire into the grounding lug, as shown in Figure 40, and use a

Chapter 3: Installing the Chassis in an Equipment Rack86

87Chapter 4Installing the Power SuppliesThis chapter explains how to install the power supplies. It has the following sections: “Protecting Against E

Chapter 4: Installing the Power Supplies88Protecting Against Electrostatic Discharge (ESD)To protect the equipment from damage by Electrostatic Discha

SwitchBlade x8112 Chassis Switch Installation Guide89Installing the AT-SBxPWRSYS1 AC System Power SupplyFor background information on the AT-SBxPWRSYS

9FiguresFigure 1: AT-SBx8112 Chassis ...

Chapter 4: Installing the Power Supplies90Figure 44. Removing the Blank Slot Cover from Power Supply Slot C3. Remove the new AT-SBxPWRSYS1 Power Suppl

SwitchBlade x8112 Chassis Switch Installation Guide91Figure 45. Items Included with the AT-SBxPWRSYS1 Power Supply ModuleNoteStore the packaging mater

Chapter 4: Installing the Power Supplies924. Check the power supply for its model name, shown in Figure 46, to verify the module.If the module is the

SwitchBlade x8112 Chassis Switch Installation Guide936. Align and insert the AT-SBxPWRSYS1 Power Supply into the power supply slot. Figure 48 shows th

Chapter 4: Installing the Power Supplies947. Lower the power supply locking handle to secure the power supply to the chassis, as shown in Figure 49.Fi

SwitchBlade x8112 Chassis Switch Installation Guide95Installing the AT-SBxPWRPOE1 PoE Power SupplyThis section contains the installation procedure for

Chapter 4: Installing the Power Supplies96Figure 50. Removing the Blank Slot Cover from Power Supply Slot A3. Remove the power supply from the shippin

SwitchBlade x8112 Chassis Switch Installation Guide97Figure 51. Items Included with the AT-SBxPWRPOE1 Power Supply ModuleNoteStore the packaging mater

Chapter 4: Installing the Power Supplies984. Check the model name, shown in Figure 52, to verify the module.If the module is the AT-SBxPWRSYS1 System

SwitchBlade x8112 Chassis Switch Installation Guide99Figure 54. Inserting the AT-SBxPWRPOE1 Power Supply