Allied Telesis Switch AT-S110 Manuel d'utilisateur Page 336
- Page / 386
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 27: Cable Diagnostics
336
Port: This parameter displays the port (cable) selected.
Test Results: Displays the diagnostic results for each pair in the
cable. One of the following cable status parameters is displayed:
OK: There is not problem detected with the cable.
Open in Cable: There is an open wire within the cable.
Short in Cable: Two wires are shorted together within the
cable.
Cross talk in Cable: There is crosstalk detected between one
pair of wires and another pair within the cable.
Cable Fault Distance: This parameter specifies the distance
from the switch port to the cable fault.
Cable Length: This parameter specifies the length of the cable
connected to the switch port.
Note
If length is displayed as “N/A” it means the cable length is “Not
Available”. This is due to the port being unable to obtain cable
length/either because its link speed is 10M or 100M, or the cables
used are broken and/or of bad in quality.
Note
The deviation of “Cable Fault Distance” is +/-2 meters, therefore No
cable may be displayed under Test Result, when the cable used is
less than 2 m in length.
- AT-GS950/10PS 1
- Contents 3
- List of Figures 9
- List of Tables 13
- Document Conventions 16
- Getting Started 19
- Chapter 1 21
- Switch’s IP Address 22
- Web Browser Tools 25
- System Configuration 27
- System Management Information 28
- IP Access List Configuration 32
- Delete an IP 33
- Address List 33
- Add New User 34
- Name and 34
- Password 34
- Modify User 35
- Delete User Name 36
- User Interface Configuration 37
- User Interface 38
- System Time 39
- Setting Daylight 41
- Parameters 41
- SSL Settings 42
- 4. Click Apply 43
- DHCP Client Configuration 45
- DHCP Auto Configuration 47
- System Information Display 48
- System Log Configuration 50
- Bridge Configuration 53
- Port Configuration 55
- Chapter 3: Port Configuration 58
- STP and RSTP 61
- Bridge Priority 63
- Path Costs and Port Costs 64
- Port Priority 64
- Forwarding 65
- Delay and 65
- Topology 65
- Point-to-Point and Edge Ports 66
- Mixed STP and 67
- RSTP Networks 67
- Spanning Tree 68
- Chapter 4: STP and RSTP 70
- Configure RSTP Port Settings 73
- Configure the 75
- Advanced RSTP 75
- Spanning Tree Topology 78
- Chapter 5 79
- VLAN Mapping 86
- Modify MST 87
- Instance 87
- Delete MST 87
- Topology Information 90
- Static Port Trunking 93
- Create a Port Trunk 97
- Modify a Port Trunk 99
- Disable a Port Trunk 101
- LACP Port Trunks 103
- Overview 104
- System Priority 105
- Port Priority Value 106
- General Guidelines 107
- Chapter 7: LACP Port Trunks 108
- Group Status 109
- Configuration 110
- Port Priority Configuration 112
- Port Mirroring 113
- Port Mirroring Configuration 115
- Chapter 8: Port Mirroring 116
- Disable Port Mirroring 117
- Loopback Protection 119
- MAC Address Table 123
- Chapter 10: MAC Address Table 126
- Modify Static Unicast Address 128
- Delete Static Unicast Address 129
- IGMP Snooping 135
- IGMP Snooping Configuration 138
- Chapter 11: IGMP Snooping 140
- Storm Control 141
- Ingress Rate 143
- Limiting 143
- Egress Rate 143
- Ingress Rate Limiting 146
- Egress Rate Limiting 148
- Virtual LANs 149
- VLAN Overview 150
- Port-based 151
- Tagged VLAN 152
- VLAN Index 153
- VLAN Name 153
- Tagged and Untagged Ports 153
- Port VLAN Identifier (PVID) 153
- General Rules for 154
- Creating a 154
- Assign Ports to a VLAN Mode 155
- Chapter 13: Virtual LANs 156
- Tagged VLAN Configuration 157
- Modify a Tagged 158
- Delete a Tagged 160
- Tagged VLAN Port Settings 162
- Port-Based VLAN Configuration 164
- Modify a Port 165
- Based VLAN 165
- Chapter 14 167
- Overview and Guidelines 168
- General Configuration 169
- Port Settings 170
- Time Settings 172
- Chapter 14: GVRP 174
- Chapter 15 175
- Egress Queue vs 177
- Packet Priority 177
- Prioritizing 178
- Untagged Packets 178
- Queue Scheduling Algorithm 185
- Advanced Features 187
- SNMPv1 and v2c 189
- SNMPv1 and SNMPv2c Overview 190
- Trap Receiver Attributes 191
- Activate SNMP Interface 192
- Create User and 193
- Group Names 193
- Modify User and 194
- Delete User and 195
- SNMP Community Strings 196
- SNMP Traps 198
- Modify a Trap 199
- Host Table Entry 199
- Delete a Trap 199
- Chapter 16: SNMPv1 and v2c 200
- Chapter 17 201
- SNMPv3 Privacy 203
- Protocol 203
- SNMPv3 MIB 203
- SNMPv3 User and Group Names 206
- Chapter 17: SNMPv3 208
- SNMPv3 View Names 209
- Modifying 211
- SNMPv3 View 211
- Deleting SNMPv3 211
- View Names 211
- SNMPv3 View Table 212
- SNMPv3 Traps 215
- Access Control Configuration 217
- Classifier 219
- Modifying a 221
- Deleting a 222
- Profile Action 224
- Modifying Profile 225
- Deleting a Profile 226
- In-Profile Action 227
- Modifying an In 229
- Deleting an In 230
- Out-Profile Action 231
- Modify Out 233
- Delete Out 234
- Port List 235
- “Create Policy,” next 238
- “Modify Policy” on page 240 238
- “Delete Policy” on page 241 238
- Policy Sequence Status 243
- Chapter 19 245
- Enable and Disable RMON 247
- Port Statistics 248
- Histories 250
- Chapter 19: RMON 252
- Voice VLAN 257
- Dynamic Auto 259
- Detection vs 259
- Static Ports 259
- Chapter 20: Voice VLAN 260
- OUI Setting 265
- Modify OUI 266
- Delete OUI 266
- Security 267
- Port Access Control 268
- Port Access 269
- Chapter 21: Security 270
- RADIUS Client 273
- Radius Client 274
- Dial-in User 276
- Modify a Dial-in User 277
- Delete a Dial-in User 278
- Destination MAC Filter 279
- Destination MAC 280
- Power Over Ethernet (PoE) 283
- PoE Configuration 286
- Chapter 23 289
- DHCP Snooping 290
- DHCP with 292
- Option 82 292
- VLAN Setting 296
- Chapter 23: DHCP Snooping 298
- Binding Database 300
- Chapter 24 303
- Global Configuration 305
- Enabling or 306
- Disabling LLDP 306
- Displaying 307
- Information 307
- Setting Port 307
- Chapter 24: LLDP 308
- Neighbors Information 309
- Network Statistics 311
- Traffic Comparison Statistics 313
- Error Group Statistics 316
- Historical Status Charts 318
- Section IV 321
- Chapter 26 323
- File Upload 329
- File Download 331
- Cable Diagnostics 335
- Chapter 27: Cable Diagnostics 336
- Rebooting the AT-GS950/10PS 337
- Switch Reboot 338
- Disabling Factory 342
- Default Reset 342
- Enabling Factory 344
- Pinging a Remote System 347
- MSTP Overview 349
- Resolving VLAN 352
- Fragmentation 352
- Multiple VLANs 353
- Assigned to an 353
- Appendix A: MSTP Overview 354
- VLAN and MSTI Associations 356
- Ports in Multiple MSTIs 357
- MST Region 360
- Guidelines 360
- Associating VLANs to MSTIs 363
- Summary of Guidelines 367
- Appendix B 369
- Parameter 376
- Default Setting 376
- Specifications 376
Produits connexes et manuels pour Logiciel Allied Telesis Switch AT-S110
(248 pages)
(49 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels