Allied Telesis AT-S80 Guide de l'utilisateur Page 33
- Page / 242
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
AT-S80 Management Software User’s Guide
Section I: Using the Menus Interface 33
Enabling and Disabling the DHCP Client
This procedure explains how to activate and deactivate the DHCP client
on the switch. When the client is activated, the switch obtains its IP
configuration from a DHCP server on your network. Note the following
before performing the procedure:
The switch does not need an IP address, subnet mask, or default
gateway for normal network operations. These parameters must be
assigned values only if you plan to remotely manage the device with a
web browser from a management workstation on your network.
A gateway address is only required if your remote management station
is separated from the switch by a router.
The default setting for the DHCP client is disabled.
The DHCP client does not support BOOTP servers.
To activate or deactivate the DHCP client, perform the following
procedure:
1. From the Main Menu, type B to select Basic Switch Configuration.
The Basic Switch Configuration Menu is shown in Figure 4 on page 30.
2. From the Basic Switch Configuration Menu, type I to select System IP
Configuration.
The System IP Configuration Menu is shown in Figure 5 on page 31.
3. Type D to select Enable/Disable DHCP Mode.
The following prompt is displayed:
Enable or Disable DHCP mode (E/D)>
4. Type E to select Enable or D to select Disable.
If activated, the client immediately begins to send queries to the DHCP
server. It continues to send queries until it receives a response.
5. Type Q to select Quit to previous menu and save your changes.
- User’s Guide 1
- Contents 3
- Document Conventions 13
- Contacting Allied Telesyn 14
- Overview 15
- Management Overview 16
- Local Management Connection 17
- Remote Management Connection 18
- Management Access Level 19
- AT-FS750/24 Switch 20
- Using the Menus Interface 21
- Interface 23
- Enter system location> 35
- Enter system contact> 35
- Enter current password> 37
- Enter new password> 38
- Retype new password> 38
- Enter old password> 38
- Viewing Switch Information 39
- Rebooting the Switch 42
- Enter new timeout value> 45
- Figure 12. Ping Results 46
- Chapter 4: Port Configuration 50
- Enabling and Disabling a Port 52
- Enter new mode for port 53
- (a/h/H/f/F/T)> 53
- Port Trunking Overview 58
- Trunk” on page 65 59
- (E/D)> 62
- Chapter 5: Port Trunking 64
- Enter trunk group number> 65
- Port Mirroring Overview 68
- Chapter 6: Port Mirroring 70
- VLAN Features 74
- Port-based VLANs 75
- Tagged VLANs 75
- Port-based VLAN Overview 76
- Drawbacks of 78
- Example 1 79
- Example 2 80
- Tagged VLAN Overview 82
- Tagged VLAN 84
- Enter port number > 88
- Chapter 7: Virtual LANs 90
- QoS Overview 98
- Chapter 9 107
- RSTP Overview 108
- Path Costs and Port Costs 109
- Port Priority 110
- Point-to-Point and Edge Ports 111
- Point-to-Point Ports 112
- (Full-duplex Mode) 112
- RSTP Networks 113
- Mixed STP and 113
- Rapid Spanning 114
- Tree and VLANs 114
- Enabling or Disabling RSTP 115
- Enter bridge priority> 118
- Enter bridge hello time> 118
- Enter bridge maximum age> 119
- Configuring STP Compatibility 120
- Configuring the 121
- Basic RSTP Port 121
- Settings 121
- Advanced RSTP 123
- Port Settings 123
- Displaying the RSTP Topology 126
- Chapter 10 129
- Authentication 131
- Authenticator 131
- Port-based 133
- Network Access 133
- Guidelines 133
- Switch A 135
- Switch B 135
- Enter port number> 137
- Chapter 11 141
- RADIUS Overview 142
- Configuring the RADIUS Client 143
- Enter response time> 144
- Broadcast Storm Control 147
- Management Software Updates 151
- Enter file name> 154
- Enter retry count> 154
- Download file? (Y/N)> 154
- Section II 155
- Chapter 14 157
- Switch’s IP Address 158
- Web Browser Tools 161
- Basic Switch Parameters 163
- System Contact 168
- 3. Click Apply 168
- Console UI Idle Time Out 170
- Web Server 170
- User name and password 170
- Viewing System Information 172
- DHCP Mode 174
- Client” on page 166 174
- Rebooting a Switch 175
- Pinging a Remote System 176
- 3. Click Start 177
- Port Configuration 179
- 10/100BaseTX - Base ports 181
- Displaying Port Statistics 186
- Port Trunking 189
- Creating a Port Trunk 190
- Modifying a Port Trunk 192
- Chapter 17: Port Trunking 194
- Port Mirroring 195
- Configuring Port Mirroring 196
- Disabling Port Mirroring 197
- Chapter 18: Port Mirroring 198
- Virtual LANs 199
- Creating a VLAN 200
- Chapter 19: Virtual LANs 202
- Displaying the VLANs 204
- Figure 60 205
- Modifying a VLAN 206
- Deleting a VLAN 208
- Quality of Service (QoS) 209
- Chapter 21 215
- Basic RSTP Configuration 216
- Bridge Forward Delay 218
- 5. Click Apply 222
- Viewing the RSTP Topology 223
- Chapter 22 225
- Chapter 23 229
- Appendix A 237
Produits connexes et manuels pour Logiciel Allied Telesis AT-S80
(63 pages)
(49 pages)
(20 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels