Allied-telesis AT-S79 Manuel d'utilisateur Page 250
- Page / 348
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 22: Port Configuration
250 Section II: Using the Web Browser Interface
100M/Half - 100 Mbps in half-duplex mode
100M/Full - 100 Mbps in full-duplex mode
1000M/Half - 1000 Mbps in half-duplex mode
1000M/Full - 1000 Mbps in full-duplex mode
When selecting a setting, note the following:
When a twisted-pair port is set to Auto-Negotiation, the default
setting, the end node should also be set to Auto-Negotiation to
prevent a duplex mode mismatch. A switch port using Auto-
Negotiation defaults to half-duplex if it detects that the end node is
not using Auto-Negotiation. This can result in a mismatch if the end
node is operating at a fixed duplex mode of full-duplex. To avoid
this problem when connecting an end node with a fixed duplex
mode of full-duplex to a switch port, disable Auto-Negotiation on
the port and set the port’s speed and duplex mode manually.
Allied Telesis does not recommend manually setting a 10/100/
1000Base-T twisted-pair port to either 1000 Mbps full duplex or
1000 Mbps half duplex. For 1000 Mbps operation, Allied Telesis
recommends setting the port to Auto-Negotiation.
The only valid setting for an optional SFP port is Auto-Negotiation.
Flow Control
The current flow control setting on the port. The switch uses a special
pause packet to notify the end node to stop transmitting for a specified
period of time. The possible values are:
Enabled - The port is allowed to use flow control. This is the default
setting for all ports on the switch.
Disabled - The port does not use flow control.
3. Click Apply to save the configuration.
- User’s Guide 1
- Contents 3
- Document Conventions 15
- Contacting Allied Telesis 16
- Overview 17
- Management Overview 18
- Local Management Connection 19
- Remote Management Connection 20
- Remote SNMP Management 21
- Management Access Level 22
- AT-GS950/24 Switch 23
- Chapter 1: Overview 24
- Using the Menus Interface 25
- Interface 27
- Enter new subnet mask> 36
- Enter system location> 39
- Enter system contact> 39
- Enter entry number> 42
- Enter new user name> 42
- Enter new password> 42
- Retype new password 44
- Retype new password> 44
- Viewing Switch Information 45
- Rebooting the Switch 48
- Enter new timeout value> 51
- Figure 12. Ping Results 52
- Displaying Statistics 55
- Chapter 4: Port Configuration 60
- Enabling and Disabling a Port 63
- Enter new mode for port 64
- (a/h/H/F/f/t/T)> 64
- Port Trunking Overview 68
- Static Port Trunk Guidelines 69
- (E/D)> 72
- Enter trunk group number> 74
- IGMP Snooping Overview 76
- Setting the Age 80
- Setting Group 80
- Chapter 6: IGMP Snooping 82
- Static Multicast Address 83
- Adding a Static 85
- Multicast 85
- Deleting a Static 86
- Member Port 87
- Port Mirroring Overview 90
- Chapter 8: Port Mirroring 92
- Dial-in User Configuration 95
- Configuring a Dial-in User 97
- Deleting a Dial-in 98
- Modifying a Dial 100
- Virtual LANs 101
- VLAN Overview 102
- Port-based VLANs 103
- Tagged VLANs 103
- Port-based VLAN Overview 104
- Tagged VLAN Overview 105
- Identifier 106
- General Rules for 106
- Creating a 106
- Tagged VLAN 106
- Port VLAN 106
- Creating a VLAN 107
- Chapter 10: Virtual LANs 108
- Changing the 113
- Changing Port 114
- VLAN Type 114
- Displaying the VLANs 115
- Modifying a VLAN 118
- Enter new VLAN name> 119
- Deleting a VLAN 120
- Deleting a Tagged 121
- Chapter 11 123
- SNMP Overview 124
- Community String Attributes 125
- Creating an SNMP Community 128
- Deleting an 130
- Community 130
- Modifying an 131
- Enter community name> 132
- Creating an SNMP Host 133
- Deleting an Host 134
- Host Entry 135
- Enter IP address for host> 136
- Enabling an 137
- SNMP Trap 137
- Deleting a Trap 139
- Receiver 139
- Modifying a Trap 139
- Enabling or 141
- Disabling Traps 141
- Quality of Service (QoS) 143
- QoS Overview 144
- Configuring CoS 150
- Chapter 13 155
- RSTP Overview 156
- Path Costs and Port Costs 157
- Port Priority 158
- Point-to-Point and Edge Ports 159
- Point-to-Point Ports 160
- (Full-duplex Mode) 160
- Mixed STP and 161
- RSTP Networks 161
- Rapid Spanning 162
- Tree and VLANs 162
- Enabling or Disabling RSTP 163
- Enter bridge priority> 166
- Enter bridge hello time> 166
- Enter bridge maximum age> 167
- Configuring STP Compatibility 168
- Configuring the 169
- Basic RSTP Port 169
- Settings 169
- Advanced RSTP 171
- Port Settings 171
- Displaying the RSTP Topology 174
- Bandwidth Control 177
- Bandwidth Control Overview 178
- Configuring Bandwidth Control 179
- Setting the 180
- Ingress Limit 180
- Setting Ingress 180
- DLF Status 181
- Chapter 14: Bandwidth Control 182
- IP Access List 183
- IP Access List Overview 184
- Configuring IP Access List 185
- Adding or 186
- Removing IP 186
- Addresses 186
- Destination MAC Filtering 187
- Destination MAC 189
- Filtering 189
- Removing 190
- Chapter 17 191
- Authentication 193
- Authenticator 193
- Port-based 195
- Network Access 195
- Guidelines 195
- Switch A 197
- Switch B 197
- Guest VLANs 198
- Enter port number> 200
- Enter guest VLAN ID > 201
- Chapter 18 207
- RADIUS Overview 208
- Configuring the RADIUS Client 209
- Management Software Updates 213
- Enter file name> 216
- Enter retry count> 216
- Download file? (Y/N)> 216
- Section II 217
- Chapter 20 219
- Switch’s IP Address 220
- Web Browser Tools 223
- Basic Switch Parameters 225
- Setting Up the IP Access List 228
- Deleting an IP 229
- System Contact 232
- 3. Click Apply 232
- Adding System 233
- Administration 233
- Information 233
- Modifying 234
- Deleting 235
- Viewing System Information 238
- Rebooting a Switch 241
- Pinging a Remote System 243
- Port Configuration 247
- Port Trunking 251
- Creating a Port Trunk 252
- Modifying a Port Trunk 254
- Chapter 23: Port Trunking 256
- Port Mirroring 257
- Configuring Port Mirroring 258
- Disabling Port Mirroring 259
- Chapter 24: Port Mirroring 260
- Chapter 25 261
- Deleting a Group MAC Address 265
- IGMP Snooping 267
- Configuring IGMP Snooping 268
- Chapter 26: IGMP Snooping 270
- Chapter 27 271
- Removing a MAC Address 274
- Chapter 28: Bandwidth Control 278
- Assigning Ports to a VLAN 280
- Creating a Tagged VLAN 281
- Chapter 29: Virtual LANs 282
- Modifying a Tagged VLAN 283
- Deleting a Tagged VLAN 284
- Creating a Port-Based VLAN 285
- Modifying a Port-Based VLAN 286
- Deleting a Port-Based VLAN 287
- Chapter 30 289
- Modifying an SNMP Community 291
- Deleting an SNMP Community 292
- Creating a Host Table 293
- Modifying a Host Table Entry 294
- Deleting a Host Table Entry 295
- Enabling or Disabling Traps 296
- Modifying Traps 297
- Deleting Traps 298
- Chapter 32 305
- Basic RSTP Configuration 306
- Viewing the RSTP Topology 313
- Chapter 33 315
- Dial-in User 319
- Adding a Dial-in User 320
- Modifying a Dial-in User 321
- Deleting a Dial-in User 322
- Chapter 35 323
- Statistics 325
- Displaying Switch Statistics 326
- Chapter 36: Statistics 328
- Displaying Error 330
- Group Statistics 330
- Displaying 332
- Historical Status 332
- Appendix A 341
Produits connexes et manuels pour Matériel informatique Allied-telesis AT-S79
Matériel informatique Allied-telesis Broadcom Advanced Control Suite 3 Manuel d'utilisateur
(80 pages)
(80 pages)
Matériel informatique Allied-telesis AlliedView-EMS 4.0.2 VLAN-Manager Manuel d'utilisateur
(77 pages)
(77 pages)
Matériel informatique Allied-telesis AlliedView-EMS 4.0.2 INSTALLATION Manuel d'utilisateur
(31 pages)
(31 pages)
Matériel informatique Allied-telesis AlliedView-EMS 4.0.2 QoS-Manager Manuel d'utilisateur
(146 pages)
(146 pages)
Audyssey Odbiornik podręczniki użytkownika
Lista Audyssey Odbiornik produkty zawierają 1 instrukcje obsługi do modeli 1. Wszystkie podręczniki użytkownika w formacie pdf są dostępne do pobrania lub obejrzenia online.
Commentaires sur ces manuels