Allied-telesis AT-FS970M Series Manuel d'utilisateur Page 199
- Page / 330
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
AT-FS970M Series Version 2.3.1.0 Web Interface User’s Guide
199
2. Enter the following settings:
IP Address— Enter the IP address of the TACACS+ server. The IP
address must be in the following IPv4 format: xxx.xxx.xxx.xxx.
Key— Enter the encryption key for TACACS+ communications
between the switch and TACACS+ server. The key must match the
encryption key used by the TACACS+ server. The maximum
length is 40 characters. Special characters are allowed, but spaces
are not permitted.
3. Click Apply.
4. Click SAVE
to save your changes to the startup configuration file.
- AT-FS970M Series 1
- Copyright 2
- Contents 10
- Document Conventions 16
- Contacting Allied Telesis 18
- Browser Interface 19
- Management Sessions 20
- Web Manager Accounts 21
- Starting a Management Session 23
- Figure 1. Login Page 26
- Logging onto the Switch 27
- What to Configure First 30
- Setting System 31
- When You Do 32
- Not Know the IP 32
- Address of the 32
- Baud rate: 9600 33
- Data bits: 8 33
- Parity: None 33
- Stop bits: 1 33
- Flow control: None 33
- Enabling HTTP 35
- Service in the 35
- Saving your 36
- Changes in the 36
- Saving Your Changes 37
- 8 on page 37 38
- Basic Switch Parameters 39
- Configuring an 40
- SNTP or NTP 40
- Time Manually 43
- Managing Local User Accounts 52
- Changing a User 53
- Password 53
- Changing the 54
- User Privilege 54
- Deleting a User 55
- 5. Click Delete User 56
- Rebooting a Switch 57
- Upgrading the Software 58
- Displaying System Information 61
- Setting Port Parameters 63
- Port Numbers on the Switch 64
- Changing the Port Settings 67
- Setting Port Statistics 75
- Displaying Port Statistics 76
- Receive Statistics 77
- Transmit 79
- Statistics 79
- Interface 80
- Clearing Port Statistics 82
- Reloading Statistics 83
- Port Mirroring 85
- Assigning a Destination Port 88
- Specifying Direction Type 89
- 6. Click Apply 90
- 7. Click SAVE 90
- Chapter 6: Port Mirroring 92
- Chapter 7 93
- Setting the MAC Address 101
- Chapter 9 111
- Overview 112
- Displaying LACP Trunks 113
- Adding an LACP Trunk 115
- Modifying an LACP Trunk 117
- Deleting an LACP Trunk 119
- Setting Static Port Trunks 121
- Adding Static Trunks 125
- Deleting Static Trunks 129
- Chapter 11 131
- Tagged and 133
- Untagged Ports 133
- Displaying VLANs 134
- Adding a VLAN 135
- Modifying VLANs 137
- Assigning a Native VLAN 139
- Deleting VLANs 142
- Chapter 12 143
- (IGMP) Snooping 149
- Disabling IGMP Snooping 154
- Displaying the Routers List 155
- Clearing the Routers List 156
- Displaying the Hosts List 157
- IGMP Snooping Querier 159
- Assigning 161
- Multiple Queriers 161
- .2 Enabled Enabled Active 163
- .3 Enabled Disabled None 163
- .4 Enabled Enabled Standby 163
- Guidelines 164
- VLAN— VLAN ID 165
- Power Over Ethernet (PoE) 169
- Prioritization 171
- Displaying PoE Port Settings 172
- Chapter 16 179
- Interface— Port ID 182
- RADIUS and TACACS+ Clients 187
- Server 1 190
- Configuring 191
- Remote Manager 191
- Authentication 191
- Using RADIUS 191
- Adding a 193
- RADIUS Server 193
- Using TACACS+ 195
- Chapter 18 201
- Authenticator Role: 203
- Single host mode 203
- Multiple host mode 204
- Multiple supplicant mode 204
- Dynamic VLAN 205
- Assignments 205
- Chapter 19 215
- IP Management 217
- Displaying IPv4 Interfaces 218
- Adding an IPv4 Address 219
- Changing an IPv4 Address 220
- Deleting an IPv4 Address 222
- Displaying the IPv6 Interface 223
- Adding an IPv6 Address 225
- Changing IPv6 Addresses 227
- 5. Click Apply 228
- 6. Click SAVE 228
- Deleting IPv6 Addresses 229
- Access Control Lists (ACL) 231
- Creating an ACL 235
- Assigning an ACL to Ports 239
- Displaying a List of ACLs 241
- Setting Static Routes 243
- Displaying Static Routes 244
- Adding a Static Route 245
- 8. Click Apply 246
- 9. Click SAVE 246
- Deleting a Static Route 247
- Displaying the Routing Table 248
- Quality of Service (QoS) 251
- Creating a QoS Policy 255
- Chapter 23 263
- Changing the RIP Settings 270
- Displaying RIP Statistics 272
- Reloading RIP Statistics 274
- Managing the ARP Table 275
- Displaying the ARP Table 277
- Adding a Static ARP Entry 278
- Deleting ARP Entries 280
- LLDP and LLDP-MED 281
- Optional LLDP-MED TLVs: 283
- Chapter 25: LLDP and LLDP-MED 284
- Disabling LLDP on the Switch 287
- Configuring LLDP on a Port 288
- Selecting LLDP TLVs on a Port 290
- Figure 127. LLDP TLV Page 291
- 5. Click Edit 291
- Creating a Civic 294
- Location Entry 294
- Figure 129. Locations Tab 295
- 5. Click Add 296
- Creating a 298
- Coordinate 298
- Location 298
- Displaying LLDP Statistics 309
- Displaying Location Entries 311
- Displaying 312
- Locations 312
- Displaying ELIN 313
- Displaying the 314
- Basic LLDP 314
- Configuration 314
- Displaying LLDP 315
- Port Assignments 315
- Displaying Port 316
- LLDP-MED TLV 318
- - Model Name 319
- - Asset ID 319
- Chapter 26 321
- Specifying an sFlow Collector 324
- Chapter 26: sFlow 326
- Configuring sFlow on a Port 327
- Enabling sFlow on the Switch 329
- Displaying the sFlow Settings 330
Produits connexes et manuels pour Matériel informatique Allied-telesis AT-FS970M Series
(288 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels