Allied-telesis AT-SBx3106WMB Manuel d'utilisateur

613-001941 Rev. AAT-SBx3106WMBWall Mounting Brackets for theAT-SBx3106 Access Edge Chassis SwitchInstallation Guide

Preface10

11Installation InstructionsThe following instructions explain how to install the AT-SBx3106 Chassis on a wall with the AT-SBx3106WMB Wall Mounting Bra

Installation Instructions12AT-SBx3106 Chassis and AT-SBx3106WMB BracketsFigure 1 illustrates the AT-SBx3106 Chassis as it looks on the wall with the A

AT-SBx3106WMB Wall Mounting Brackets Installation Guide13Required ToolsThis section lists the tools necessary for installing the chassis on a wall wit

Installation Instructions14Selecting a Wall LocationThe following sections contain information on how to select a wall location for the chassis.Minimu

AT-SBx3106WMB Wall Mounting Brackets Installation Guide15Figure 2. Minimum Area Dimensions When the Chassis has AC Power SuppliesThe front panel shoul

Installation Instructions16Figure 3. Minimum Area Dimensions When the Chassis has DC Power SuppliesThe minimum space on the back panel of the chassis

AT-SBx3106WMB Wall Mounting Brackets Installation Guide17Figure 4. Brackets Aligned with Wallboard Studs The brackets should NOT be fasten intra-stud

Installation Instructions18General WallRequirementsPlease perform the following procedure to determine the suitability of the site for the chassis:1.

AT-SBx3106WMB Wall Mounting Brackets Installation Guide19Figure 6. 100 - 125 VAC 125 V NEMA 5-20 Plug and Receptacle

Copyright  2014 Allied Telesis, Inc.All rights reserved. No part of this publication may be reproduced without prior written permission from Allied T

Installation Instructions20Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to install the chassis.NoteThe

AT-SBx3106WMB Wall Mounting Brackets Installation Guide21WarningPower cord is used as a disconnection device. To de-energize equipment, disconnect the

Installation Instructions22CautionRisk of explosion if battery is replaced by an incorrect type. Replace only with the same or equivalent type recomme

AT-SBx3106WMB Wall Mounting Brackets Installation Guide23NoteIf installed in a closed or multi-unit rack assembly, the operating ambient temperature o

Installation Instructions24WarningHigh Leakage Current exists in this chassis. Connect external ground wire before connecting AC power supply(s).  E4

AT-SBx3106WMB Wall Mounting Brackets Installation Guide25Checking the Components of the AT-SBx3106WMB BracketsCheck the shipping package for the items

Installation Instructions26Marking the Wall Locations for the Screw HolesTo mark the screw holes for the brackets on the wall, perform the following p

AT-SBx3106WMB Wall Mounting Brackets Installation Guide2731.0 cm (12 in.) to 15.0 cm (6 in.). If you are installing the chassis on wallboard, be sure

Installation Instructions28Figure 10. Marking the Screw Holes for the Bottom Bracket4. Double-check the measurements of the marks on the wall for the

AT-SBx3106WMB Wall Mounting Brackets Installation Guide29Figure 11. Screw Hole Measurements5. Go to “Installing the Screws in the Wall” on page 30.50.

3Preface ...

Installation Instructions30Installing the Screws in the WallThis section contains instructions on how to install the provided screws in the wall.Warni

AT-SBx3106WMB Wall Mounting Brackets Installation Guide31Wallboard To install the four 2 1/2” wood screws, perform the following procedure:1. Use a dr

Installation Instructions32Installing the Brackets on the ChassisThis procedure installs the wall brackets on the chassis.NoteDo not remove the shippi

AT-SBx3106WMB Wall Mounting Brackets Installation Guide33Figure 14. Removing the Equipment Rack Brackets2. Turn the chassis upside down on a table or

Installation Instructions34Figure 16. Attaching the Wall Mounting Brackets to the Chassis4. Go to “Installing the Chassis on the Wall” on page 35.

AT-SBx3106WMB Wall Mounting Brackets Installation Guide35Installing the Chassis on the WallTo install the chassis on the wall, perform the following p

Installation Instructions362. Gently lower the chassis until it is resting on the screws. Refer to Figure 18.NoteAs a safety precaution, the individua

AT-SBx3106WMB Wall Mounting Brackets Installation Guide37Figure 19. Installing the Washers4. Tighten the four bracket screws to secure the brackets an

Installation Instructions38Figure 20. Tightening the Screws5. Go to “Installing the Vent Covers” on page 39.

AT-SBx3106WMB Wall Mounting Brackets Installation Guide39Installing the Vent CoversTo install the vent covers, perform the following procedure:1. Slid

Contents4

Installation Instructions402. Secure the vent cover to the chassis with two screws. Refer to Figure 22.Figure 22. Securing the Top Vent Cover

AT-SBx3106WMB Wall Mounting Brackets Installation Guide413. Slide the second vent cover over the bottom vents. The tabs on the cover fit into the slot

Installation Instructions424. Secure the bottom vent cover with the two remaining screws. Refer to Figure 24.Figure 24. Securing the Bottom Vent Cover

AT-SBx3106WMB Wall Mounting Brackets Installation Guide43This completes the procedure for installing the chassis on the wall. Refer to the SBx3106 Cha

Installation Instructions44

5FiguresFigure 1: AT-SBx3106 Chassis Switch with the AT-SBx3106WMB Wall Mounting Brackets ... 12Figure 2: Minimum Area Dimensio

List of Figures6

7PrefaceThis guide contains instructions on how to install the AT-SBx3106 Chassis on a wall with the AT-SBx3106WMB Wall Mounting Brackets. This prefac

Preface8Safety Symbols Used in this DocumentThis document uses the following conventions.NoteNotes provide additional information.CautionCautions info

AT-SBx3106WMB Wall Mounting Brackets Installation Guide9Contacting Allied TelesisIf you need assistance with this product, you may contact Allied Tele