Allied-telesis AT-FS705L Manuel d'utilisateur

613-001267 Rev. AFast Ethernet SwitchAT-FS705LInstallation Guide

Preface10Where to Find Web-based GuidesThe installation and user guides for all Allied Telesis products are available in portable document form (PDF)

AT-FS705L Fast Ethernet Switch Installation Guide11Contacting Allied Telesis This section provides Allied Telesis contact information for technical su

12Chapter 1Product DescriptionThis chapter contains the follows sections: “Overview” on page 13 “Key Features” on page 14 “Hardware Feature Descrip

AT-FS705L Fast Ethernet Switch Installation Guide13OverviewThe AT-FS705L switch is an unmanaged five-port Fast Ethernet switch. This switch offers a r

Chapter 1: Product Description14The AT-FS705L switch features five 10/100 Mbps ports. Each twisted pair port has an RJ-45 connector with a maximum ope

AT-FS705L Fast Ethernet Switch Installation Guide15Hardware Feature DescriptionThe sections below describe the hardware features of the AT-FS705L Fast

Chapter 1: Product Description16For 10 Mbps operation, Category 3 or better 100 ohm shielded or unshielded twisted pair cabling is required. For 100 M

AT-FS705L Fast Ethernet Switch Installation Guide17AC PowerConnectorThe AT-FS705L Fast Ethernet switch has a single AC power supply socket on the back

Chapter 1: Product Description18A Few Ethernet Switching BasicsAn Ethernet switch interconnects network devices, such as workstations, printers, route

AT-FS705L Fast Ethernet Switch Installation Guide19Duplex Mode Duplex mode refers to how an end node receives and transmits data. If an end node can r

Copyright © 2009 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Chapter 1: Product Description20A port operating in full-duplex mode uses PAUSE frames, as specified in the IEEE 802.3x standard, to stop the transmis

21Chapter 2InstallationThis chapter contains the following sections: “Reviewing Safety Precautions” on page 22 “Selecting a Site for the Switch” on

Chapter 2: Installation22Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to install the switch. NoteThe 

AT-FS705L Fast Ethernet Switch Installation Guide23Warning: As a safety precaution, install a circuit breaker with a minimum value of 15 Amps between

Chapter 2: Installation24Selecting a Site for the SwitchObserve the following requirements when choosing a site for the AT-FS705L Fast Ethernet switch

AT-FS705L Fast Ethernet Switch Installation Guide25Planning the InstallationTable 3 contains the cabling specifications for the twisted pair ports.Not

Chapter 2: Installation26Unpacking the SwitchTo unpack an AT-FS705L switch, perform the following procedure:1. Remove all components from the shipping

AT-FS705L Fast Ethernet Switch Installation Guide27Installing the Switch on a Table or DesktopTo install the switch on a table or desktop, perform the

Chapter 2: Installation28Wall-Mounting the SwitchYou can mount the switch vertically on a wall using the mounting brackets that come with the unit. Th

AT-FS705L Fast Ethernet Switch Installation Guide297. Align the switch horizontally. And then position and hang the switch onto the wall using the two

3Electrical Safety and Emissions StandardsThis product meets the following standards.EMI FCC Class B, CISPR 22 Class B, EN55022 Class B, C-TICK, CEImm

Chapter 2: Installation30Cabling the SwitchTo connect the twisted pair cables to the ports on the AT-FS705L switch, perform the following procedure:1.

AT-FS705L Fast Ethernet Switch Installation Guide31Powering On the SwitchTo apply power to the AT-FS705L switch without the optional power cord retain

32Chapter 3TroubleshootingThis chapter contains information on how to troubleshoot the switch in the event a problem occurs.NoteIf you are still unabl

33Appendix ATechnical SpecificationsPhysical SpecificationsDimensions: (W x D x H)160 mm x 116 mm x 35 mm(6.3 in x 4.57 in x 1.44 in)Weight: 0.5 kg (1

Appendix A: Technical Specifications34Safety and Electromagnetic Emissions CertificationsEMI FCC Part 15 Class B, CISPR 22 Class B, EN55022 Class B, I

AT-FS705L Fast Ethernet Switch Installation Guide35RJ-45 Twisted Pair Port ConnectorsThis section lists the connectors and connector pinouts for the A

4Translated Safety StatementsImportant: The  indicates that a translation of the safety statement is available in a PDF document titled “Translated S

5Preface ...

Contents6

7Figure 1. AT-FS705L Front Panel...

8PrefaceThis guide contains instructions on how to install the AT-FS705L Fast Ethernet switch. This preface contains the following sections: “Safety

AT-FS705L Fast Ethernet Switch Installation Guide9Safety Symbols Used in this DocumentThis document uses the safety symbols defined in Table 1.Table 1