Allied-telesis x600-48Ts/XP Manuel d'utilisateur Page 41
- Page / 94
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide
41
AT-StackXG Modules, Cables, and Connections
The stacks are connected via the stacking ports on the VCS Stacking
Modules (AT-StackXG), which are installed in the back of each switch.
The following cables are used to connect the stacking ports of x600 series
switches:
High Speed Stacking Cables (0.5 meter) - StackXG/0.5
High Speed Stacking Cables (1.0 meter) - StackXG/1
This configuration, shown in Figure 15,
uses two switches that are
connected back to back via two high-speed stacking links. Note that
stacking ports labeled 1 must connect to stacking ports labeled 2. In this
configuration the stack can still function using only a single high speed
link.
Figure 15. Back-to-Back Topology (x600 Switches)
RPS INPUT
100-240VAC~
AT-StackXG
AT-StackXG
RPS INPUT
100-240VAC~
AT-StackXG
AT-StackXG
STACK PORT 1
STACK PORT 2
High Speed Stacking Cables (0.5 meter)
Model Number AT-StackXG/0.5
STACK PORT 1 STACK PORT 2
- Installation Guide 1
- Product Documentation 4
- Starting a Management Session 5
- Contacting Allied Telesis 8
- Radiated Energy 9
- Industry Canada 9
- Translated Safety Statements 10
- Contents 11
- List of Figures 13
- List of Tables 15
- Overview 17
- Introduction 18
- Switch Descriptions 19
- Connector 20
- AC Power 20
- RPS Connector 22
- Distance 23
- Auto-MDI/ 24
- SFP Transceiver Slots 25
- XFP Transceiver Slots 26
- Redundant Twisted Pair Ports 27
- SD Card Slot 28
- Port LEDs 29
- XFP Transceiver 30
- Slot LEDs 30
- System Status LEDs 31
- Stack LEDs 32
- Terminal Port 34
- AT-LBM (Loop Back) Module 36
- RPS INPUT 36
- 100-240VAC~ 36
- VCS Stacking Module 37
- AT-StackXG 37
- STACK PORT 1 37
- STACK PORT 2 37
- AC Power Connector 38
- Virtual Chassis Stacking 39
- Introduction 40
- uses two switches that are 41
- Recovery States 42
- Resiliency Link 44
- Configurations 44
- Resilient Stacked 45
- Topology 45
- Stack Formation 46
- Selecting the Stack Master 46
- Common Stack Configuration 47
- Stack Management VLAN 47
- Stack Member Identification 48
- Management IP Addresses 49
- Fallback Action 50
- Re-elect New Stack Master 50
- Recombining Separated Stacks 50
- Adding a Stack Member 51
- Replacing a Stack Member 51
- Repairing a Broken Stub 51
- Installing the Hardware 53
- Reviewing Safety Precautions 54
- Unpacking a Switch 56
- 100-240VAC 57
- Resetting the Switch 60
- Installing the 62
- Cabling the Network Ports 65
- Twisted Pair 66
- Specifications 66
- Transceiver 67
- Installing an SFP 68
- SFP Handle 69
- 4741 43 45 70
- 42 44 46 70
- Installing an XFP 71
- Powering on a Switch 74
- Starting a Local 75
- Management 75
- Warranty Registration 76
- Troubleshooting 77
- Power LED is Off 78
- SFP or XFP LED is Off 80
- System Fault LED is Blinking 82
- Chapter 5: Troubleshooting 84
- Technical Specifications 87
- Power Specifications 88
- Certifications 88
Produits connexes et manuels pour Matériel informatique Allied-telesis x600-48Ts/XP
Matériel informatique Allied-telesis AlliedView-EMS 4.0.2 Device-Manager Manuel d'utilisateur
(441 pages)
(441 pages)
Matériel informatique Allied-telesis AlliedView-EMS 4.0.1 INSTALLATION Manuel d'utilisateur
(32 pages)
(32 pages)
Matériel informatique Allied-telesis AlliedView-EMS 4.0.1 VLAN MANAGER Manuel d'utilisateur
(72 pages)
(72 pages)
Matériel informatique Allied-telesis AlliedView-EMS 4.0.1 QoS MANAGER Manuel d'utilisateur
(146 pages)
(146 pages)
ABC Office 20612 C Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Aktenvernichter ABC Office 20612 C.
Wir stellen 1 PDF-Handbücher ABC Office 20612 C zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commentaires sur ces manuels