Allied-telesis AT-2972SX Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel informatique Allied-telesis AT-2972SX. Allied Telesis AT-2972SX User Manual [en] Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 18
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
613-001255 Rev. B
Network Adapters
AT-2711FX
AT-2712FX
AT-2812FX
AT-2912T
AT-2916SX
AT-2931SX
AT-2972SX
Linux User’s Guide
Vue de la page 0
1 2 3 4 5 6 ... 17 18

Résumé du contenu

Page 1 - Linux User’s Guide

613-001255 Rev. BNetwork AdaptersAT-2711FXAT-2712FXAT-2812FXAT-2912TAT-2916SXAT-2931SXAT-2972SXLinux User’s Guide

Page 2

Enabling LINUX10IntroductionThis chapter describes the tg3 Linux driver for the Broadcom NetXtreme-based Allied Telesis PCI/PCI-X/PCI Express Ethernet

Page 3 - Contents

Network Adapters Linux User’s Guide11Installing the LINUX TG3 FileThere are two procedures to install the Linux TG3 file: “Installing the Source RPM

Page 4

Enabling LINUX12NoteThe force option may be needed on some Linux distributions if conflicts are reported.Depending on the kernel, the driver is instal

Page 5

Network Adapters Linux User’s Guide13Enter the following command:make KVER=<kernel_version>where <kernel_version> in the form of 2.x.y-z i

Page 6

Enabling LINUX14On Red Hat distributions, you can specify “ethtool -s” parameters in the ifcfg-ethx scripts using the ETHTOOL_OPTS keyword. The specif

Page 7

Network Adapters Linux User’s Guide15MTU 1500 (range 46 - 9000)Rx Ring Size 200 (range 0 - 511)Rx Jumbo Ring Size 100 (range 0 - 255)Tx Ring Size 511

Page 8 - Contacting Allied Telesis

Enabling LINUX16Unloading and Removing the Driver To unload the driver, use the ifconfig command to bring down all eth# interfaces opened by the drive

Page 9

Network Adapters Linux User’s Guide17Driver MessagesThe following messages are the most common sample messages that are logged in the /var/log/message

Page 10 - Introduction

Enabling LINUX18

Page 11 - Installing the LINUX TG3 File

Copyright  2009 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Page 12 - Source TAR File

3ContentsPreface ...

Page 14

5PrefaceThis guide contains instructions on how to configure the following Allied Telesis adapters using the Linux driver software: AT-2711FX AT-271

Page 15

Preface6Safety Symbols Used in this DocumentThis document uses the safety symbols defined in Table 1.Table 1. Safety SymbolsSymbol Meaning Description

Page 16 - Enabling LINUX

Network Adapters Linux User’s Guide7Where to Find Web-based GuidesThe installation and user guides for all Allied Telesis products are available in po

Page 17

Preface8Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales or corporate informa

Page 18

9Chapter 1Enabling LINUXThis chapter describes how to enable the LINUX System on the Allied Telesis adapters. This chapter contains the following sect

Commentaires sur ces manuels

Pas de commentaire